Bedienungsanleitung Husqvarna LB448S (Seite 8 von 140) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

579204

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

SAFETY INSTRUCTIONS

8 – English

Basic mowing technique

General

• Mowing slopes can be dangerous. Do not use the

lawn mower on very steep slopes.

• The lawn mower should not be used on inclines

greater than 15 degrees. Inclines that are too great

can result in fuel leakage

• On sloping ground you should work along the slope. It

is much easier to work along a slope than it is to work

up and down it.

• Branches, twigs, stones, etc. should be removed from

the lawn before you start to mow.

• Never lift up the lawn mower or carry it around when

the engine is running. If you must lift the lawn mower,

ﬁrst switch off the engine and disconnect the ignition

lead from the spark plug.

• Make sure the cutter does not hit foreign objects such

as stones, roots or the like. This can make the cutter

dull and bend the engine shaft. A bent axle gives

imbalance and heavy vibration, which results in a

great risk of the cutter becoming loose.

If any foreign object is hit or if vibrations occur stop the

machine immediately. Disconnect the HT lead from

the spark plug. Check that the machine is not

damaged. Repair any damage.

• Never mow more than 1/3 of the length of the grass.

This especially applies during dry periods. Mow ﬁrst

with the cutting height set high. Then check the result

and lower to an appropriate height. If the grass is

really long, drive slowly and mow twice if necessary.

• Never run with the machine when it is running. You

should always walk with the lawn mower.

• Do not mow the lawn while walking backwards.

Machine′s safety equipment

This section describes the machine′s safety equipment,

its purpose, and how checks and maintenance should be

carried out to ensure that it operates correctly. See the

”What is what?” section to locate where this equipment is

positioned on your machine.

Cutting cover and protective cover

The cutting cover is designed to reduce vibration and to

reduce the risk of cuts. Make sure the cutting cover is not

damaged and that there are no visible defects such as

cracks.

The protective cover is designed to reduce the risk of

crush injuries and to catch a broken drive belt. Check that

the protective cover is undamaged and that it is properly

secured.

Engine brake handle

The engine brake is designed to stop the engine. When

the grip on the engine brake handle is released the engine

should stop.

Check the engine brake as follows:

Apply full throttle and then release the brake handle. The

engine should stop and the drive should disengage.

The engine brake should always be adjusted so that the

engine stops within 3 seconds.

WARNING! Make sure that your hands

and feet do not come near the cutting

attachment when the engine is running.

WARNING! Never use a machine with

faulty safety equipment. The machine's

safety equipment must be checked and

maintained as described in this section.

If your machine fails any of these checks

contact your service agent to get it

repaired.

WARNING! Never use a machine that has

faulty safety equipment! Carry out the

inspection, maintenance and service

routines listed in this section.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna LB448S Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info