Bedienungsanleitung Husqvarna LC 247i (Seite 18 von 576) (Alle Sprachen)

733927

Zoom out

Zoom in

Vorherige Seite

1/576

Nächste Seite

4. When all LEDs on the battery have come on the

battery is fully charged. Charge the battery for

maximum 24 hours.

5. To disconnect the battery charger from the mains

socket, pull the plug, not the power cord.

6. Remove the battery from the battery charger.

Battery charging status

A Husqvarna Li-ion battery can be charged or used at all

charging levels. The battery is not damaged. A fully

charged battery will not decrease its charge when the

battery is left in the charger.

LED display Charging status

LED 1 flashes 0%-25%

LED 1 is lit, LED 2 flashes 25%-50%

LED 1, LED 2 are lit, LED

3 flashes

50%-75%

LED 1, LED 2, LED 3 are

lit, LED 4 flashes

75%-100%

LED 1, LED 2, LED 3,

LED 4 are lit

Fully charged

To start the product

1. Open the battery lid.

2. Put a charged battery in 1 of the battery holders. For

longer operation time, put a second charged battery

in the other battery holder.

3. Turn the safety key to 1. (Fig. 23)

4. Stay behind the product.

5. Push the ON/OFF button (A) on the control panel.

The display comes on. The battery indicator (B)

shows the battery charge of the 2 batteries. The

number of the battery that operates is shown

adjacent to the battery indicator. For models

LC 347iV, LC 347iVX, LC 353iV, LC 353iVX, the

display also shows the set speed. (Fig. 38)

6. Loosen the start inhibitor. (Fig. 25)

7. Push the motor brake handle in the direction of the

handlebar. (Fig. 39)

To use the drive on the wheels

(LC 347iV, LC 347iVX, LC 353iV,

LC 353iVX)

• Pull the drive bail in the direction of the handlebar to

start the drive. (Fig. 40)

• Push + and - on the control panel to set the drive

speed in 4 steps. (Fig. 41)

• Release the drive bail to disengage the drive, for

example when you go near an obstacle.

To use the SavE function

The product has a battery saving function (SavE) that

gives longer operation time.

1. Push the SavE button (A) to start the function. The

SavE symbol (B) on the display comes on.

2. Push the SavE button again to stop the function. The

SavE symbol (B) on the display goes out. (Fig. 42)

The SavE function stops automatically if the ground

conditions make it necessary to have a higher output.

The SavE function starts automatically again when the

ground conditions let it.

High load function

When the product cuts long or wet grass, the motor

automatically increases rpm. The motor goes back to

standard mode when high load is not necessary.

To stop the product

The product stops automatically if you do not operate it

for 10 minutes. Always turn the safety key to 0 before

you let the product out of view.

1. Release the motor brake handle to stop the motor.

(Fig. 24)

2. Push the ON/OFF button on the control panel. All

LED lights and symbols on the display go out. (Fig.

43)

3. Open the battery lid and turn the safety key to 0.

(Fig. 44)

4. To remove the battery, push the 2 release buttons

and pull out the battery. (Fig. 45)

5. Charge the battery if it is weak. For more

information, refer to

To charge the battery on page

To get a good result

• Always use a sharp blade. A blunt blade gives an

irregular result and the cut surface of the grass

becomes yellow. A sharp blade also uses less

energy than a blunt blade.

• Do not cut more than ⅓ of the length of the grass.

Cut first with the cutting height set high. Examine the

result and lower the cutting height to an applicable

level. If the grass is very long, drive slowly and cut 2

times if necessary.

• Cut in different directions each time to prevent

stripes in the lawn.

To cut grass without a grass catcher or

mulch plug attached

• Lift up the rear cover and remove the grass catcher.

• If a mulch plug and a mulch blade are attached,

remove them.

• Close the rear cover before you operate the product.

1199 - 003 - 28.04.2020

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna LC 247i Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info