Bedienungsanleitung Husqvarna LC 347iV (Seite 17 von 576) (Alle Sprachen)

733928

Zoom out

Zoom in

Vorherige Seite

1/576

Nächste Seite

Operation

Introduction

WARNING: Before you operate the product,

you must read and understand the safety

chapter.

Husqvarna Connect

Husqvarna Connect is a free app for your mobile device.

The Husqvarna Connect app gives extended functions

for your Husqvarna product:

• Extended product information.

• Information about, and help with, product parts and

servicing.

To start to use Husqvarna Connect

1. Download the Husqvarna Connect app on your

mobile device.

2. Register in the Husqvarna Connect app.

3. Do the instruction steps in the Husqvarna Connect

app to connect and register the product.

Bluetooth

information (LC 247iX,

LC 347iVX, LC 353iVX)

Bluetooth

wireless technology

The symbol for

Bluetooth

wireless technology comes

on when your mobile device is connected to the product.

(Fig. 32)

To set the product in operation position

1. Fold the handle to upright position. (Fig. 33)

2. Move the knobs up in the direction of the handle until

they stop and you hear a click. (Fig. 27)

3. Tighten the knobs fully.

To set the cutting height

The cutting height can be adjusted in 6 levels.

1. Move the cutting height lever down to decrease the

cutting height.

2. Move the cutting height lever up to increase the

cutting height. (Fig. 34)

CAUTION:

Do not set the cutting height too

low. The blades can hit the ground if the

surface of the lawn is not level.

Battery

WARNING: Before you use the battery, you

must read and understand the safety

chapter. You must also read and understand

the operator's manual for the battery and the

battery charger.

Battery status

The display shows the remaining battery capacity and if

there are problems with the battery. The battery capacity

is shown for 5 seconds after the product is switched off

or the battery indicator button is pressed. The warning

symbol on the battery is on when an error has occurred.

See

Battery on page 20

(Fig. 35)

LED lights

Battery status

All LEDs are lit Fully charged (75-100%)

LED 1, LED 2, LED 3 are

lit

The battery is 50%-75%

charged

LED 1, LED 2 are lit The battery is 25%-50%

charged

LED 1 is lit The battery is 0%-25%

charged.

LED 1 flashes The battery is empty.

Charge the battery.

To charge the battery

Charge the battery before the first use. The battery is

only 30% charged when supplied to the customer.

Note:

The battery charger must be connected to the

voltage and frequency specified on the rating plate.

The battery does not charge if the battery temperature is

above 50°C. The battery charger decreases the

temperature of the battery before it starts to charge.

1. Connect one end of the power cord for the battery

charger into the socket of the battery charger.

2. Connect the other end of the power cord for the

battery charger in an grounded mains socket. The

LED on the battery charger flashes green one time.

(Fig. 36)

3. Put the battery in the battery charger. The green light

on the charger comes on when the battery is

correctly connected to the battery charger. (Fig. 37)

1199 - 003 - 28.04.2020

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna LC 347iV Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info