Bedienungsanleitung Husqvarna LC 347V (Seite 11 von 400) (Alle Sprachen)

733920

Zoom out

Zoom in

Vorherige Seite

1/400

Nächste Seite

3. Fill the fuel tank. See

To fill fuel on page 11

4. Fill the oil tank and do a check of the oil level. See

To do a check of the oil level on page 13

To fill fuel

If available, use low-emission/alkylate gasoline. If low-

emission/alkylate gasoline is not available, use good

quality unleaded gasoline or leaded gasoline with octane

number not less than 90.

CAUTION: Do not use gasoline with an

octane number less than 90 RON (87 AKI).

This can cause damage to the product.

1. Open the fuel tank cap slowly to release the

pressure.

2. Fill slowly with a fuel can. If you spill fuel, remove it

with a cloth and let remaining fuel dry off.

3. Clean the area around the fuel tank cap.

4. Tighten the fuel tank cap fully. If the fuel tank cap is

not tightened, there is a risk of fire.

5. Move the product a minimum of 3 m (10 ft) from the

position where you filled the tank before a start.

To set the cutting height

The cutting height can be adjusted in 6 levels.

1. Move the cutting height lever rearward to decrease

the cutting height.

2. Move the cutting height lever forward to increase the

cutting height. (Fig. 33)

CAUTION:

Do not set the cutting height too

low. The blades can hit the ground if the

surface of the lawn is not level.

To start the product

• Make sure that the ignition cable is connected to the

spark plug.

Manual start (not on LC 347VI, LC 353VI)

1. For LC 247, LC 247S: The very first time you start

the product, press the primer bulb 5 times. The next

time you start the product when the engine is cold,

press the primer bulb 3 times.

2. Stay behind the product.

3. Hold the engine brake handle against the handlebar.

(Fig. 34)

4. Hold the starter rope handle with your right hand.

5. Slowly pull out the starter rope until you feel some

resistance.

6. Pull with force to start the engine.

WARNING: Do not twist the starter rope

around your hand.

Electrical start (LC 347VI, LC 353VI)

1. Make sure that the battery is activated and charged.

See

To start the battery on page 13

2. Attach the battery to the engine. (Fig. 35)

3. Push the start inhibitor out to the right (A).

4. Pull the start bar (B) against the handlebar to start

the starter motor. The starter motor stops when the

engine starts. (Fig. 24)

To use the drive on the wheels

• For LC 247S, LC 247SP: Pull the drive bail in the

direction of the handlebar. (Fig. 36)

• For LC 347V, LC 347VI, LC 353V, LC 353VI: Start

the drive on the wheels with the speed control lever

on the left side of the handle. Move the speed

control lever forward to increase the speed and

rearward to decrease the speed. (Fig. 37)

• Before you pull the product rearward, disengage the

drive and push the product forward approximately

10 cm.

• Release the drive bail to disengage the drive, for

example when you go near an obstacle.

To stop the product

• To stop the engine, release the engine brake handle.

To remove the battery

To prevent accidental start of the engine, remove the

battery on model LC 347VI, LC 353VI when the product

is not in operation.

1. Press the lock buttons (A) and pull the battery out.

(Fig. 38)

To get a good result

• Always use a sharp blade. A blunt blade gives an

irregular result and the cut surface of the grass

becomes yellow. A sharp blade also uses less

energy than a blunt blade.

• Do not cut more than ⅓ of the length of the grass.

Cut first with the cutting height set high. Examine the

result and lower the cutting height to an applicable

level. If the grass is very long, drive slowly and cut 2

times if necessary.

• Cut in different directions each time to prevent

stripes in the lawn.

808 - 004 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna LC 347V Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info