Bedienungsanleitung Husqvarna LC 347VI (Seite 10 von 400) (Alle Sprachen)

733921

Zoom out

Zoom in

Vorherige Seite

1/400

Nächste Seite

Assembly

Introduction

WARNING: Before you assemble the

product, read the safety chapter. On

LC 347VI, LC 353VI, also remove the

battery.

To assemble the handle

1. Loosen the lower knobs.

2. Move the knobs to the lower end of the grooves on

the left and the right side of the product. (Fig. 25)

3. Set the handle height in one of the 2 available

positions.

4. Move the knobs up in the direction of the handle until

they stop and you hear a click. (Fig. 26)

5. Tighten the knobs fully.

To set the product in transport position

1. Loosen the lower knobs.

2. Move the knobs to the lower end of the grooves on

the left and the right side of the product. (Fig. 25)

3. Fold the handle forward. (Fig. 27)

To set the product in operation position

1. Fold the handle to upright position. (Fig. 28)

2. Move the knobs up in the direction of the handle until

they stop and you hear a click. (Fig. 26)

3. Tighten the knobs fully.

To assemble the grass catcher

1. Attach the grass catcher frame to the grass bag with

the rigid part of the bag on the bottom. Keep the

handle of the frame on top of the grass bag. (Fig. 29)

2. Attach the bottom section of the grass catcher frame

in the groove on the bottom of the grass catcher.

3. Attach the grass bag to the grass catcher frame with

the clips. (Fig. 30)

4. Lift the rear cover.

5. Attach the grass catcher to the top edge of the

chassis.

6. Put the lower part of the grass catcher into the grass

discharge channel. (Fig. 31)

To assemble the mulch plug

(accessory)

1. Lift up the rear cover and remove the grass catcher.

2. Put the mulch plug into the discharge channel. (Fig.

32)

3. Replace the blade with the mulch blade that is

supplied in the mulch kit. Refer to

To replace the

blade on page 13

To cut grass without a grass catcher or

mulch plug attached

• Lift up the rear cover and remove the grass catcher.

• If a mulch plug and a mulch blade are attached,

remove them.

• Close the rear cover before you operate the product.

When you operate the product, the cut grass discharges

below the rear cover.

Operation

Introduction

WARNING: Before you operate the product,

you must read and understand the safety

chapter.

Husqvarna Connect

Husqvarna Connect is a free app for your mobile device.

The Husqvarna Connect app gives extended functions

for your Husqvarna product:

• Extended product information.

• Information about, and help with, product parts and

servicing.

To start to use Husqvarna Connect

1. Download the Husqvarna Connect app on your

mobile device.

2. Register in the Husqvarna Connect app.

3. Do the instruction steps in the Husqvarna Connect

app to connect and register the product.

Before you operate the product

1. Read the operator's manual carefully and make sure

that you understand the instructions.

2. Examine the cutting equipment to make sure that it

is correctly attached and adjusted. See

To examine

the cutting equipment on page 12

10 808 - 004 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna LC 347VI Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info