Bedienungsanleitung Husqvarna LC 353AWD (Seite 12 von 404) (Alle Sprachen)

733941

Zoom out

Zoom in

Vorherige Seite

1/404

Nächste Seite

• Let an approved Husqvarna service agent do

servicing on the product regularly.

• Replace damaged, worn or broken parts.

Assembly

Introduction

WARNING: Before you assemble the

product, you must read and understand the

safety chapter.

WARNING: Remove the spark plug cable

from the spark plug before you assemble the

product.

To assemble the handle

1. Lift the lower handle. (Fig. 21)

2. Align the holes at the bottom of the lower handle with

the holes in the handle brackets.

Note: Select the holes that give the best operation

position.

3. Tighten the lower handle knobs.

4. Lift the upper handle and align it with the lower

handle.

5. Tighten the upper handle knobs fully.

To install the starter rope handle

1. Attach the loop for the starter rope and the T-knob.

Do not tighten fully. (Fig. 22)

2. Hold the engine brake handle against the handlebar.

3. Slowly pull out the starter rope and put it into the

loop for the starter rope. (Fig. 23)

4. Tighten the T-knob. (Fig. 24)

To set the product in transport position

1. Remove the grass catcher.

2. Loosen the lower handle knobs to unlock the handle.

(Fig. 25)

3. Fold the handle down rearward.

4. Remove the knobs and the pins on the lower handle.

5. Fold the handle forward.

To assemble the grass catcher

1. Attach the grass catcher frame to the grass bag with

the rigid part of the bag on the bottom. Keep the

handle of the frame out of the top of the bag. (Fig.

26)

2. Attach the grass bag to the frame with the quick-

action clips. (Fig. 27)

Operation

Introduction

WARNING: Before you operate the product,

you must read and understand the safety

chapter.

Before you operate the product

1. Read the operator's manual carefully and make sure

that you understand the instructions.

2. Examine the cutting equipment to make sure that it

is correctly attached and adjusted. See

To examine

the cutting equipment on page 15

3. Fill the fuel tank. See

To fill fuel on page 12

4. Fill the oil tank and do a check of the oil level. See

To do a check of the oil level on page 11

To fill fuel

If available, use low-emission/alkylate gasoline. If low-

emission/alkylate gasoline is not available, use good

quality unleaded gasoline or leaded gasoline with octane

number not less than 90.

CAUTION: Do not use gasoline with an

octane number less than 90 RON (87 AKI).

This can cause damage to the product.

1. Open the fuel tank cap slowly to release the

pressure.

2. Fill slowly with a fuel can. If you spill fuel, remove it

with a cloth and let remaining fuel dry off.

3. Clean the area around the fuel tank cap.

4. Tighten the fuel tank cap fully. If the fuel tank cap is

not tightened, there is a risk of fire.

5. Move the product a minimum of 3 m (10 ft) from the

position where you filled the tank before a start.

To set the cutting height

The cutting height can be adjusted in 9 levels.

12 1242 - 003 - 01.11.2019

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna LC 353AWD Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info