Bedienungsanleitung Husqvarna LC 551iV (Seite 19 von 604) (Alle Sprachen)

733939

Zoom out

Zoom in

Vorherige Seite

1/604

Nächste Seite

sure that children and persons

that are not approved cannot

get access to the product,

battery or battery charger.

Assembly

Introduction

WARNING: Read and understand the safety

chapter before you assemble the product.

To install and remove the multi battery

(accessory)

1. Remove the 4 rubber covers and the 4 screws from

the motor cover. (Fig. 23)

2. Put the adapter plate onto the motor cover.

3. Attach the adapter plate with the 4 supplied screws

to a torque of 5-6 Nm. (Fig. 24)

4. Open the battery hatch.

5. Remove the battery in slot 1. (Fig. 25)

6. Remove the seal stop. (Fig. 26)

7. Push the battery adapter into the battery

compartment until you hear a click. (Fig. 27)

8. Put the cord of the battery adapter through the seal

stop hole. Attach the cord with the clip. (Fig. 28)

9. Install the multi battery onto the battery adapter.

10. Connect the multi battery to the battery adapter. (Fig.

29)

11. Attach battery adapter cord to the handle with the 3

fabric straps. (Fig. 30)

12. Remove the multi battery in the opposite sequence.

WARNING:

Do not attach the cord too

loosely to the handle. The cord can come off

the handle and cause injury.

To assemble the handle (LC 551iV)

1. Loosen the lower knobs.

2. Move the knobs to the lower end of the grooves on

the left and the right side of the product. (Fig. 31)

3. Set the handle height in one of the 2 available

positions.

4. Move the knobs up in the direction of the handle until

they stop and you hear a click. (Fig. 32)

5. Tighten the knobs fully.

To assemble the handle (LB 548i)

1. Remove the handle nut and the washer from the

plate on the upper handle.

2. Put the upper handle in position on top of the lower

handle.

CAUTION: Make sure that the wires are

not caught or become damaged.

3. Attach the washer and the handle adjustment lever.

(Fig. 33)

4. Turn the handle to the side for a good operation

position when you operate the product near a wall.

(Fig. 34)

To assemble the grass catcher (LC

551iV)

1. Attach the grass catcher frame to the grass bag with

the rigid part of the bag on the bottom. Keep the

handle of the frame on top of the grass bag. (Fig. 35)

2. Attach the bottom section of the grass catcher frame

in the groove on the bottom of the grass catcher.

3. Attach the grass bag to the grass catcher frame with

the clips. (Fig. 36)

4. Lift the rear cover.

5. Attach the grass catcher to the top edge of the

chassis.

6. Put the lower part of the grass catcher into the grass

discharge channel. (Fig. 37)

To assemble the mulch plug (LC 551iV

accessory)

1. Lift up the rear cover and remove the grass catcher.

2. Put the mulch plug into the discharge channel. (Fig.

38)

3. Replace the blade with the mulch blade that is

supplied with the mulch kit. Refer to

To replace the

blade on page 23

1336 - 003 - 17.12.2019

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna LC 551iV Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info