Bedienungsanleitung Husqvarna R 316TsX AWD (Seite 12 von 156) (Englisch, Italienisch, Portugiesisch, Spanisch)

733962

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

• The ignition cables are removed from the

plugs.

WARNING: The exhaust fumes from the

engine contain carbon monoxide, an

odourless, poisonous and very dangerous

gas. Do not run the product in closed spaces

or spaces with not sufficient air flow.

WARNING: Read the warning instructions

that follow before you use the product.

• For best performance and safety, do maintenance

on the product regularly as given in the maintenance

schedule. See

Maintenance schedule on page 18

• Electrical shocks can cause injuries. Do not touch

the cables when the engine is on. Do not do a

function test on the ignition system with your fingers.

• Do not start the engine if the protective covers are

removed. There is a high risk of injury caused by

moving or hot parts.

• Let the product become cool before you do

maintenance near the engine.

• The blades are sharp and can cause cuts. Wind

protection around the blades or use protective

gloves when you do work on the blades.

• Always put the cutting deck in servicing position to

clean it. Do not park the product near the edge of a

ditch or slope to get access to the cutting deck.

CAUTION: Read the caution instructions

that follow before you use the product.

• Do not turn over the engine if the spark plug or

ignition cable is removed.

• Make sure that all nuts and bolts are tightened

correctly and that the equipment is in good condition.

• Do not change the adjustment of governors. If the

engine speed is too high, the product components

can become damaged. See

Technical data on page

for highest permitted engine speed.

• The product is approved only with the equipment

supplied or recommended by the manufacturer.

Assembly

Introduction

WARNING: The drive belt tension spring can

break and cause injury. Wear protective

glasses when you attach or remove the

cutting deck.

Read the assembly instructions in the owner's manual

carefully. A label on the inner side of the front cover on

the product, also shows how to attach and remove the

cutting deck.

To attach the cutting deck

1. Park the product on level ground.

2. Apply the parking brake.

3. Set the cutting height lever in the servicing position.

4. Set the lift lever for the cutting deck in the mow

position.

5. Put the drive belt as shown to make sure that it does

not get caught and break when the cutting deck is

attached.

6. Push the equipment frame down. Lift the service lock

to vertical position.

WARNING: The lock mechanism

can cause injury to fingers if you do

not operate it carefully. Put the

service lock in full vertical position

and hold the front edge of the

cutting deck with two hands when

you continue to the next step.

12 844 - 007 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna R 316TsX AWD Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna R 316TsX AWD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info