Bedienungsanleitung Husqvarna Rider 216T AWD (Seite 10 von 136) (Englisch, Italienisch, Portugiesisch, Spanisch)

733957

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

• Discard replaced batteries. See

Disposal on page

• Explosive gases can come from the battery. Do not

smoke near the battery. Keep the battery away from

open flames and sparks.

Safety instructions for maintenance

WARNING: The product is heavy and can

cause injury or damage to property or the

adjacent area. Do not do maintenance on

the engine or the cutting deck without these

conditions:

• The engine is off.

• The product is parked on a level surface.

• The parking brake is applied.

• The ignition key is removed.

• The cutting deck is disengaged.

• The ignition cables are removed from the

plugs.

WARNING: The exhaust fumes from the

engine contain carbon monoxide, an

odourless, poisonous and very dangerous

gas. Do not run the product in closed spaces

or spaces with not sufficient air flow.

WARNING: Read the warning instructions

that follow before you use the product.

• For best performance and safety, do maintenance

on the product regularly as given in the maintenance

schedule. See

Maintenance schedule on page 15

• Electrical shocks can cause injuries. Do not touch

the cables when the engine is on. Do not do a

function test on the ignition system with your fingers.

• Do not start the engine if the protective covers are

removed. There is a high risk of injury caused by

moving or hot parts.

• Let the product become cool before you do

maintenance near the engine.

• The blades are sharp and can cause cuts. Wind

protection around the blades or use protective

gloves when you do work on the blades.

• Always put the cutting deck in servicing position to

clean it. Do not park the product near the edge of a

ditch or slope to get access to the cutting deck.

CAUTION: Read the caution instructions

that follow before you use the product.

• Do not turn over the engine if the spark plug or

ignition cable is removed.

• Make sure that all nuts and bolts are tightened

correctly and that the equipment is in good condition.

• Do not change the adjustment of governors. If the

engine speed is too high, the product components

can become damaged. See

Technical data on page

for highest permitted engine speed.

• The product is approved only with the equipment

supplied or recommended by the manufacturer.

Assembly

Introduction

WARNING: The drive belt tension spring

can break and cause injury. Wear protective

glasses when you attach or remove the

cutting deck.

Read the assembly instructions in the owner's manual

carefully. A label on the inner side of the front cover on

the product, also shows how to attach and remove the

cutting deck.

To remove and attach the cutting

deck

1. Park the product on level ground.

2. Apply the parking brake.

3. Set the cutting height lever in the servicing position.

4. Release the clip on the front cover with the tool

attached to the ignition key, and lift off the cover.

5. Lift the cutting height stay and put it in the holder for

the cutting height stay.

10 850 - 003 - 14.11.2018

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna Rider 216T AWD Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna Rider 216T AWD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info