Bedienungsanleitung Husqvarna Sweeper 44 - 586636501 (Seite 7 von 23) (Alle Sprachen)

579226

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Safety

Read and understand the vehicle manual

and these instructions before using this

sweeper. Always instruct other users

before they operate the sweeper.

Symbols

Oil

Grease

Operation

Risk of Injury

• Never allow children to handle the

sweeper

• Never allow anyone to ride on the

sweeper.

• Always wear footwear when working

with the sweeper.

• Never operate the sweeper if foreign

matter is stuck in the brushes. Turn off

the vehicle engine, remove the foreign

matter and check for damage. If the

sweeper is damaged, repair before

continuing to operate.

Risk of Overturning

• Check the loading capacity of the towing

vehicle and only sweep appropriate

amounts of grass and leaves into the

grass bag.

• On starting off, make sure that the

sweeper retains its balance and does

not overturn.

• Do not work on slopes greater than 10°.

• Do not exceed 6 mph (9.6 km/h).

• Drive slowly and carefully, especially

when turning and on uneven ground.

Note: The driving and braking

characteristics depend on the towed load.

Risk of Fire

• Always keep the sweeper away from



brushes and grass bag and could cause

the bag to burn.

• Always empty the grass bag before

storing the sweeper; spontaneous

combustion may occur.

Attaching the Sweeper to Tow

Vehicle (See Figure 19)

• 

level ground.

• Attach the sweeper to the tractor hitch.

• Arrange hitch brackets and spacers into

one of the possible combinations as



Setting the Brush Height

(See Figure 20)

• To adjust sweeper brushers to best

operating height, loosen adjustment

knob and lift up on height adjustment

lever to raise the brush, or push down

on the lever to lower the brush. Best

adjustment is when brush setting is 1/2”

down into the grass.

Emptying the Grass Bag

• Stop the towing vehicle and turn off the

engine.

• 

rope.

Using the Offset Hitch

• Loosen the two nuts on the drawbar

bracket.

• Slide the drawbar to the left or right end

of the sweeper housing.

• Tighten the two nuts on the drawbar

bracket.

Using the Transport Feature

• Use the transport feature when moving

across pavement or areas you do not

want to sweep.

• 



• Pull out on the height adjustment knob

and set to the "T" position.

Maintenance

Lubricate the wheel bearings once during

the season. Remove hub cap and apply a

few drops of light oil.

Lubricate the brush axle at the beginning

and end of the season.

Clean and grease drive gears every two

years (See Figure

22). Remove hub cap

(1), bolt (2), washer (3), wheel (4), step

spacer (8), and nut (9).

Service

Replace the Brushes

(See Figure 21)

• Remove grass bag. Only loosen bolt

and nut on the single brush retainers (1).

Do not loosen double brush retainer (2).

• Note which side of brush the bristles

overlap (3). Slide brush out.

• Install new brush with bristles overlap

(3) as before.

Wheel Gear and Pawl

(See Figure 22)

Do not remove both wheels at the same

time; parts are not interchangeable.

• Remove hub cap (1), bolt (2), washer

(3), wheel (4), step spacer (8), and

nut (9).

• 

removing snap ring (5) then remove

washers (11).

• 

removing retaining ring (5) then remove

the drive pin (7), washers (12), and

spacer (13).

• Clean all parts and replace worn parts.

• Lightly grease shaft and axle.

• Lightly grease drive pin (7) and ratchet

gear (6). Reassemble drive pin (7),

ratchet gear (6), 27 tooth gear (10),

washers (11) (12), spacer (13), and

snap rings (5) onto shafts. Lightly

grease teeth of both gears.

• Lightly grease gear teeth on wheel and

then reassemble hub cap (1), bolt (2),

washer (3), wheel (4), step spacer (8),

and nut (9).

Note: Brushes should only move during

forward rotation. If brushes rotate in both

directions, drive pin is jamming the ratchet

gear. Disassemble and make sure drive

pin moves freely.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna Sweeper 44 - 586636501 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info