477656
26
Zoom out
Zoom in
Vorherige Seite
1/340
Nächste Seite
WORKING TECHNIQUES
26 – English
Felling technique for tree tops
Safe distance
During tree maintenance work above ground level, the
working area must always be secured and marked out
with signs, tape or the like. The safe distance between the
top of the tree that is to be felled and the nearest
workplace must be at least 2 1/2 times the height of the
tree. Make sure that no-one else is in this risk zone before
or during felling.
Felling direction
The aim is to fell the tree in a position where you can limb
and cross-cut the log as easily as possible. You want it to
fall in a location where you can stand and move about
safely. The main thing to avoid is that the falling tree top
should get jammed in another tree. Taking down a
”jammed” tree top is very dangerous (see point 4 in this
section).
Once you have decided which way you want the top of the
tree to f
all y
ou must assess which way the top of the tree
would fall naturally.
Several factors affect this:
Lean of the tree
Bend
Wind direction
Arrangement of branches
Weight of snow
You may find you are forced to let the tree-top fall in its
natur
al direction because it is impossib
le or dangerous to
try to make it fall in the direction you first intended.
Another very important factor, which does not affect the
felling direction b
ut does affect your safety, is to make sure
the tree has no damaged or dead branches that might
break off and hit you during felling.
Topping a tree
Topping a tree is done using three cuts. First you make the
directional cuts, which consist of the top cut and the
bottom cut, then you finish with the felling cut. By placing
these cuts correctly you can control the felling direction
very accurately.
Directional cuts
To make the directional cuts you begin with the top cut. Try
to take your position in the tree on the right side and cut
on the pull stroke.
Next make the bottom cut so that it finishes exactly at the
end of the top cut.
The directional cuts should run 1/4 of the diameter
through the tr
unk and the angle betw
een the top cut and
bottom cut should be 45
°.
The line where the two cuts meet is called the directional
cut line.
This line should be perfectly horizontal and at
right angles (90
°) to the chosen felling direction.
!
WARNING! It takes a lot of experience to
fell a tree. Inexperienced users of chain
saws should not fell trees. Do not
attempt any task that you feel unsure of!
!
WARNING! During critical felling
operations, hearing protectors should be
lifted immediately when sawing is
completed so that sounds and warning
signals can be heard.
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

husqvarna-t425

Suche zurücksetzen

  • Demontage des kettenrades einer husqvarna kettensäge t 425 Eingereicht am 1-1-2018 20:21

    Antworten Frage melden
  • Wie kann ich das Kettenrad bei einer Husqvarna T 425 wechseln Eingereicht am 23-12-2017 18:11

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Husqvarna T425 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info