Bedienungsanleitung Husqvarna TC 242 (Seite 84 von 104) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

579237

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

02966

Fig. 2

02548

Fig. 3

Fig. 4

Fig. 1

To Level Mower

Make sure tires are properly inflated to the PSI shown on

tires. If tires are over or under inflated, it may affect the ap-

pearance of your lawn and lead you to think the mower is

not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT

1. With all tires properly inflated and if your lawn appears

unevenly cut, determine which side of mower is cutting

lower.

NOTE: As desired, you can raise the low side of mower or

lower the high side.

2. Go to side of mower you wish to adjust.

3. With a 3/4" or adjustable wrench, turn lift link adjustment

nut (A) to the left to lower the mower, or, to the right to

raise the mower (Fig. 1).

NOTE: Each full turn of adjustment nut will change mower

height about 3/16".

4. Test your adjustment by mowing some uncut grass and

visually checking the appearance. Readjust, if necessary,

until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT

1. With all tires properly inflated, park tractor on level ground

or driveway.

CAUTION: Blades are sharp. Protect your hands with gloves

and/or wrap blade with heavy cloth.

2. Raise mower to its highest position.

3. At both sides of mower, position blade at side and measure

the distance (A) from bottom edge of blade to the ground.

The distance should be the same on both sides (Fig. 2).

4. If adjustment is necessary, see steps 2 and 3 in Visual

Adjustment instructions above.

5. Recheck measurements, adjust if necessary until both

sides are equal.

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting re sults, the mower blades should

be adjusted so the front tip is 1/8" to

3/8

3/8" lower than the rear

tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves

and/or wrap blade with heavy cloth.

• Raise mower to highest position.

• Position any blade so the tip is pointing straight forward.

Measure distance (B) to the ground at front and rear tip

of the blade (Fig. 3).

• If front tip of blade is not 1/8" to

3/8

3/8" lower than the rear

tip, go to the front of tractor.

• With an 11/16" or adjustable wrench, loosen jam nut A

several turns to clear adjustment nut B.

• With a 3/4" or adjustable wrench, turn front link adjustment

nut (B) clockwise (tighten) to raise the front of mower, or,

counterclockwise (loosen) to lower the front mower (Fig. 4).

NOTE: Each full turn of the adjustment nut will change

mower height about 1/8".

• Recheck measurements, adjust if necessary until front

tip of blade is 1/8" to

3/8

3/8" lower than the rear tip.

• Hold adjustment nut in position with wrench and tighten

jam nut securely against adjustment nut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna TC 242 Seite 84

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info