Bedienungsanleitung Husqvarna TS 342 (Seite 64 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

579248

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

HEADLIGHTS

Headlights can be used without your passcode and with the

engine off.

WITH ENGINE OFF:

• Press headlight button (E) once to turn headlights on for

one minute.

• Press and hold headlight button (E) until headlights blink

twice to turn headlights on for five minutes.

NOTE!

If the engine is running and shuts off for any reason, the

headlights will also shut off.

BATTERY INDICATOR BUTTON (See Fig. 16)

The battery indicator button (F) is located on the SmartSwitch

Ignition module and is used to display the status of the battery.

The indicator will only work after the passcode has been entered

and is blinking green.

• Press and hold battery indicator button (F) for three (3)

seconds.

• The SmartSwitch Ignition Button (C) will light up and indicate

the battery status as follows:

RED Charge necessary

RED AND GREEN Charge recommended

GREEN Charge not necessary

• Press the battery indicator button (F) once to stop viewing

the battery status.

NOTE!

When the battery is too low and after the first unsuccessful start

attempt, the battery indicator button will blink for two (2) seconds

and then stay lit until battery is charged or until approximately

five (5) minutes since last attempted start.

RESETTING S

MARTSWITCH IGNITION SYSTEM PASSCODE

The SmartSwitch Ignition is preset at the factory with the default

code "321". To reset or change the passcode, the operator

does not have to be seated on the tractor.

F, E, and D are used as the numerical input buttons 1, 2, and

3 for entering the passcode.

1. Press the SmartSwitch Ignition (SSI) button (C) once (or

sit on the seat). Ensure the indicator is blinking blue.

2. Press and hold the (1) and (3) buttons (F and D) simulta-

neously for approximately three (3) seconds until the SSI

button changes to solid blue.

3. Using the numbered buttons, enter the desired passcode.

The passcode may be anywhere from one to five digits in

length.

4. After the desired passcode has been entered, press the

SSI button (C) once.

NOTE!

When the indicator flashes green, the passcode has been

accepted. If the indicator blinks red, the passcode has not been

accepted. Wait until the indicator returns to blinking blue and

repeat this procedure starting from step two (2).

MARTSWITCH IGNITION SYSTEM LIGHTS

The SmartSwitch System is equipped with courtesy lights that

are used to indicate system functions or faults.

FUNCTIONS

• The SmartSwitch Ignition (SSI) Button (C) will blink blue

while waiting for the correct passcode to be entered. The

SSI button will blink green when tractor is ready to start and

remain solid green while running.

• The park brake symbol (A) will be lit if the parking brake

has not been engaged during a start attempt.

• The blade switch symbol (B) will blink if the attachment

clutch control is not in the "DISENGAGED" position during

a start attempt.

• The Reverse Operation System (ROS) button (D) will be lit

when Reverse Operation System is in use.

• The Headlight button (E) will remain lit while headlights are

in use.

• During normal operation, the Battery Indicator button (F)

will not be lit.

FAULTS

• The SSI Button (C) will blink red for two seconds if the wrong

passcode has been entered.

• The Reverse Operation System (ROS) button (D) will blink

when there is a fault with the Reverse Operation System.

See "Reverse Operation System" in section 5 of this manual.

• After the first unsuccessful start attempt, the battery indicator

button (F) will blink for two (2) seconds and then stay lit.

This indicates that the battery voltage is below normal

operating level. While engine is in operation, this light may

also indicate a charging system failure.

• The headlight button (E) will blink when one or both of the

headlight bulbs fail.

• All indicator lights will blink in the event the engine shuts

off for unknown reasons; for example, if the engine has run

out of fuel.

SMARTSWITCH IGNITION SYSTEM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna TS 342 Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info