Bedienungsanleitung Husqvarna WB533Se (Seite 8 von 92) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

477548

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

8 – English

SAFETY INSTRUCTIONS

• Never mow more than 1/3 of the length of the grass. This

especially applies during dry periods. Mow ﬁrst with the

cutting height set high. Then check the result and lower to

an appropriate height. If the grass is really long, drive

slowly and mow twice if necessary.

• Never run with the machine when it is running. You should

always walk with the lawn mower.

Cutting height

Shut down the engine before changing the cutting height.

The cutting height adjustment is spring assisted. The cutting

height can be adjusted in 6 different steps.

Do not set the cutting height too low as there is a risk that the

cutters might hit slopes with unevenness.

• To raise the cutting height move the lever to the left and

then forward.

• To lower the cutting height move the lever to the left and

then backward.

Machine′′

′′

s safety equipment

This section describes the machine′s safety equipment, its

purpose, and how checks and maintenance should be carried

out to ensure that it operates correctly. See the ”What is

what?” section to locate where this equipment is positioned

on your machine.

Cutting cover and protective cover

The cutting cover is designed to reduce vibration and to

reduce the risk of cuts. Make sure the cutting cover is not

damaged and that there are no visible defects such as cracks.

The protective cover is designed to reduce the risk of crush

injuries and to catch a broken drive belt. Check that the

protective cover is undamaged and that it is properly secured.

Engine brake handle

The engine brake is designed to stop the engine. When the

grip on the engine brake handle is released the engine should

stop.

Check the engine brake as follows:

Apply full throttle and then release the brake handle. The

engine should stop and the drive should disengage.

The engine brake should always be adjusted so that the

engine stops within 3 seconds.

Vibration damping system

Your machine is equipped with a vibration damping system

that is designed to minimize vibration and make operation

easier.

The handlebar system's steel tube and the cutting cover are

designed to minimise the vibrations from the engine.

The machine′s vibration damping system reduces the transfer

of vibration between the engine unit/cutting equipment and

the machine′s handle unit.

WB48S e och WB53S e This model also has 4 vibration

dampers ﬁtted on the handlebar unit to further reduce

vibrations.

Check that the handles and vibration damping elements are

not damaged.

WARNING! Never use a machine with faulty

safety equipment. The machine’s safety

equipment must be checked and maintained

as described in this section. If your machine

fails any of these checks contact your

service agent to get it repaired.

WARNING! Never use a machine that has

faulty safety equipment! Carry out the

inspection, maintenance and service

routines listed in this section.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna WB533Se Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info