Bedienungsanleitung Husqvarna Z448 (Seite 19 von 244) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

733967

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

• Avoid stopping or changing speed on hills.

• If stopping is necessary, pull drive levers into

the neutral position and push outward. Engage

the park brake.

• To restart movement, release the park brake.

• Pull the control levers back to the center of

the mower and push forward to regain forward

motion.

• Make all turns slowly.

WARNING! Do not drive the rider on

terrain that slopes more than 10 degrees. Mow

slopes up and down, never side to side. Avoid

sudden directional changes.

Mowing Tips

• Observe and ag rocks and other xed objects

to avoid collisions.

• Begin with a high cutting height and reduce

it until the desired mowing result is attained.

Cut the average lawn to 6.35 cm during the

cool season and over 7.62 cm during the hot

months. For healthier and better looking lawns,

mow frequently after moderate growth.

• For best cutting performance, mow grass over

15.24 cm in height twice. Make the rst cut

relatively high; the second to the desired height.

• The mowing result will be best with a high

engine speed (the blades turn rapidly) and low

speed (the rider moves slowly). If the grass is

not too long and dense, the driving speed can

be increased without negatively aecting the

mowing result.

• The nest lawns are obtained by mowing

frequently. The lawn becomes more even and

the grass clippings more evenly distributed

over the mown area. The total time taken is not

increased as a higher operating speed can be

used without poor mowing results.

• When mowing large areas, start by turning to

the right so that clippings will discharge away

from shrubs, fences, driveways, etc. After one

or two rounds, mow in the opposite direction

making left hand turns until nished.

• Avoid mowing wet lawns. The mowing result

is poorer because the wheels sink into the soft

lawn, clumps build, and grass clippings fasten

under the cowling.

• Hose the mower deck underside with water

after each use. When cleaning, the mower deck

shall be raised into the transport position. Make

sure the mower is cooled and the engine is o.

• Use compressed air to clean top surface of

the deck. Avoid ooding water on top surface,

engine and electrical components.

• When the mulching kit is used, it is important

that the mowing interval is frequent.

Moving Machine By Hand

When pushing or pulling the mower, engage the

bypass levers. The bypass levers are located at

the front of each transmission.

1. Lower the deck if needed.

2. Move the steering controls inward out of the

park brake position.

3. Lift the seat.

4. Rotate each bypass lever to the horizontal

position.

5. Lower the seat.

6. Push the mower using the sturdy feature of

the mower's structure. Do not push the mower

with the control levers.

7. To reengage the transmission, rotate the

bypass levers to the vertical position.

OPERATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna Z448 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info