Bedienungsanleitung Huvema HU 20 SUPERTAP (Seite 8 von 20) (Englisch)

627039

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

CHANG E S AND T YPI N G ERRORS RESERVED

CHANG E S AND T YPI N G ERRORS RESERVED CHANG E S AND T YPI N G ERRORS RESERVED

7.2 Tapping

These machines have a special unit for tapping, it is a quick change device. During tapping, if you want the spindle

to reverse and to withdraw the tapping tip, just push up the grip handle (as shown in figure 7). If you want to

continue tapping, just press down the grip handle (as shown in figure 8).

Always keep the protective drill head cover closed during operation. It is controlled by a micro switch, ensuring that

the machine is switched off when the cover is opened.

7.3 Work Table aDjUsTmenT

• Loosen the clamp handle on the left hand side (figure 9).

• Turn the table handle until the table has reached its proper position (figure 10).

• Tighten the clamp handle.

7.4 Drill DepTh aDjUsTmenT

To prevent the drill or tap from going too deep into the work piece,

you can set the feeding limit by adjusting the position of the feed depth

adjustment (A, figure 11).

3-2. Operation illustration and procedure:

1. There are three T grooves in the worktable. It is used to fix the work piece.

1-1.There are two T grooves in the base, too. It is convenient for fixing the longer, heavier and larger

working piece.

(Option)

2. These machines have special design for tapping, a quick change device. During tapping, if you

want spindle to turn reversely and withdraw tapping tip, just pull up grip handle only(as shown

in Figure 12.) If you want to continue to operate, just press down grip handle. (as shown in

Figure 13.)

3. Protect safety guard shall be allocated in a proper position in operation. It is controlled by a micro

witch. (For CE)

Figure 12

Figure 13

Lock

Loose

Figure 7

Figure 8

4. Adjustment of feeding limit

To prevent unwanted penetration to work piece, the feeding limit

shall be set by adjusting the appropriate position of feeding depth

fixing button as long as the distance between the end of tool and

top surface if work piece is measured.

A. Setting of feeding depth Feed Depth Adjustment

Adjust work table position

(1)Firstly, loose the clamp handle in left hand (Figure 19)

(2)Then swing the table handle to properly position. (Figure 20)

(3)Finally tight the clamp handle. (Figure 19)

Figure 19

Figure 20

Figure 11

4. Adjustment of feeding limit

To prevent unwanted penetration to work piece, the feeding limit

shall be set by adjusting the appropriate position of feeding depth

fixing button as long as the distance between the end of tool and

top surface if work piece is measured.

A. Setting of feeding depth Feed Depth Adjustment

Adjust work table position

(1)Firstly, loose the clamp handle in left hand (Figure 19)

(2)Then swing the table handle to properly position. (Figure 20)

(3)Finally tight the clamp handle. (Figure 19)

Figure 19 Figure 20

Figure 9 Figure 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Huvema HU 20 SUPERTAP Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Huvema HU 20 SUPERTAP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info