627050
12
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
12
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
Additional safety rules
Always keep in mind that:
the machine must be switched off and disconnected from the power supply during maintenance and repairs,
clamped workpieces may only be measured when the machine is switched off.
Never lean over the machine, mind loose clothing, ties, jewellery etc. and wear a cap.
Do not remove safety devices or guards. Never use the machine while a guard is open.
Always use safety glasses for machining rough materials.
Burrs and chips should only be removed using a sweeper or other aid, never with your bare hands!
Never leave the machine running unattended.
Always wear safety glasses.
2. aTTenTion
Please read the operation manual carefully before the installation and adjustment of the machine. When the
installation is finished, check all components and perform an idle trial run before putting the machine into
operation. In case of problems, please contact your Huvema dealer.
Make sure you read all the safety instructions and follow them carefully.
3. machine appearance, applicaTions and work environmenT
3.1. machine appearance
The machine design encompasses the gear box, spindle box, column, work table, bracket, base and electrical
cabinet. The gear box is atop the spindle box. The spindle box is mounted on top of the column. The work table is
supported by the bracket, which is assembled in the middle of the column. The column sits on the base.
Figure A – Outline drawing
A1 - Electrical cabinet A5 - Lifting system
A2 - Gear box A6 - Work table
A3 - Spindle box A7 - Bracket
A4 - Column A8 - Base
3.2. applicaTions
This machine is designed for drilling, broaching, reaming, tapping, boring and similar operations. The large
drilling capacity allows for drilling of workpieces within a large size range. The machine is suitable for production
and maintenance shops.
The worktable bracket can move up and down along the column at 180°, or 45° parallel to the bracket. This
design is very flexible and easy to operate.
3.3. work environmenT
The elevation of the workshop must be 2000 m or less.
The environmental temperature should be 20° C to 40 ° C.
With a medium temperature of 20 ± 5° C, the relative humidity should not exceed 85 %.
No conductive dust allowed.
Installation in an environment with explosion danger is forbidden.
No corrosive gas or steam which may corrode metal or damage the insulation.
Keep away from the source of shocks or vibration.
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Huvema HU 30 TI wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Huvema HU 30 TI

Huvema HU 30 TI Bedienungsanleitung - Deutsch - 28 seiten

Huvema HU 30 TI Bedienungsanleitung - Holländisch - 28 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info