Bedienungsanleitung Huvema HU 32-4 TOPLINE (Seite 9 von 20) (Englisch)

627033

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

CHANG E S AND T YPI N G ERRORS RESERVED

addiTional safeTy rules

Always keep in mind that:

• the machine must be switched off and disconnected from the power supply during maintenance and repairs,

• clamped workpieces may only be measured when the machine is switched off.

Never lean over the machine, mind loose clothing, ties, jewellery etc. and wear a cap.

Do not remove safety devices or guards. Never use the machine while a guard is open.

Always use safety glasses for machining rough materials.

Burrs and chips should only be removed using a sweeper or other aid, never with your bare hands!

Never leave the machine running unattended.

2. insTrucTions for using This machine

Read the safety rules carefully and always observe them. Examine the applications of this machine and beware of

possible risks.

Always wear safety glasses!

1. Caution: This drill press in intended for use only with drill bits. The use of other accessories may be hazardous.

2. Correct drilling speeds: Factors which determine the best speed to use in any drill press operation are the kind of

material being worked on, the size of the hole, the type of drill or other cutter and the quality of the cut desired.

The smaller the drill, the greater the required RPM. In soft materials, the speed should be higher than for hard

materials.

3. Drilling in metal: Use clamps to hold the work when drilling in metal. The work should never be held with bare

hands. The flutes of the drill may seize the work at any time, especially when breaking through the stock. If the

piece is whirled out of the operator's hand, he may be injured. In any case, the drill will break when the work

strikes the column.

4. The work must be clamped firmly while drilling, any tilting, twisting or shifting results not only in a rough hole,

but also increases the risk of the drill breaking. For flat work, lay the piece on a wooden base and clamp it firmly

down against the table to prevent it from turning. If the piece is of irregular shape and cannot be laid flat on the

table, it should be securely blocked and clamped.

5. The chuck must be securely fastened to the spindle so that it can't separate from the spindle.

6. Remove the key from the chuck after adjustment.

7. The tool has to be disconnected from the power supply while the motor is being mounted or connected.

8. Secure the tool to the supporting structure if, during normal operation, there is any tendency for the tool to tip

over, slide or walk on the supporting surface.

9. The set screws of the head frame should be secured tightly before using the machine.

3. unpacking

Unpack the carton and check for the parts below:

Fig. A. Main parts Qty.

1 Head 1

2 Column with flange 1

3 Bracket 1

4 Table 1

5 Base 1

If you find any parts missing or damaged, contact your dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Huvema HU 32-4 TOPLINE Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Huvema HU 32-4 TOPLINE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info