Bedienungsanleitung Huvema HU 40 G (Seite 11 von 32) (Englisch)

627048

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

CHANG E S AND T YPI N G ERRORS RESERVED

Drilling Machine Instruction Book

Magnetic feed drilling machine operating manual (Fig14.Fig15)

1 Turning the power switch A on the side of electric box, the power indicator C lights up and the

machine is ready to start.

2 Spanning the work lamp select switch D, the machine work lamp is turned on or off.

3 Spanning

the cooling pump select switch F, the cooling pump is started or stopped.

4 The machine protective cover B is used to insure the operator safety. Closing the protective cover,

the machine is in working condition and opening it, the machine is stopped.

5 According to the depth of borehole, unlock the hand shank N to set staff gauge position and then

tighten it up.

6 Drilling or tapping function select switch G.

6.1 When the select switch G is in the “ ” position, the machine is ready to drill.

6.1.1 For drilling a hole: Spanning the hand shank M, drill head may be fed manually.

6.1.2 For drilling a hole: Pushing the button L which is on the head is fed automatically. Repressing the

button L , the magnetic clutch will release and the drill head must be fed manually.

6.1.3 Automatic feed: When the staff gauge E contacts the down micro switch the magnetic clutch

releases automatically.(Automatic feed is stopped)

6.2 When the select switch G is in “ “ position, the machine is in tapping condition.

6.2.1 Tapping: Pushing the hand shank button L, the machine main shaft may rotate in clockwise or

counterclockwise and the head is tapping or holding back.

6.2.2 Tapping: If the staff gauge E contacts the up micro switch, the main shaft can rotate in clockwise

automatically. If the staff gauge E contacts the down micro switch, the machine main shaft can rotate

in counterclockwise. (The head can automatically hold back to insure tapping in safe condition.)

7 Spanning the steering select switch J can set the main shaft rotate direction.

7.1 Drilling a hole: In general, the main shaft rotates in clockwise. If the drill head is in counterclockwise,

the steering select switch J must be spanned in counterclockwise position.

7.2 Tapping: The main shaft rotation should be determined in accordance with the screw tap rotate

direction. If not, after spanning the steering select switch J, you should push the start button L to

determine the main shaft rotation in accordance with screw tap rotate direction.

8 If the main shaft rotate, feed, tapping or drilling is set properly, push the start button K to make the

machine rotate.

9 When the machine is in working condition, spanning the steering select switch J or the select switch G,

it would be stopped. You must repress the start bottom to make the machine rotate again.

10 When the machine is in working condition, if pushing the stop button I, it must be stopped out of

power. Returning the stop button in counterclockwise direction to make it move back, the machine

can be only started again.

11 spanning the high or low speed select switch H can change the main motor speed. When the switch

H is set in “2” position, the main motor speed is high. When the switch H is set in “1” position, the

main motor speed is low.

Fig 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Huvema HU 40 G Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Huvema HU 40 G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info