Bedienungsanleitung Huvema HU 40 SUPER VARIO (Seite 7 von 24) (Englisch)

627042

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

CHANG E S AND T YPI N G ERRORS RESERVED

7. conTrol panel

• Check the power source. Push the start button to check if the motor and spindle shaft are in normal working

condition.

• Spindle speed adjustment is controlled by the speed control switch. The speed is shown in the digital speed

indicator.

• In case of an emergency, push the emergency button.

• Drill/tap switch: for changing the machine from drilling mode to tapping mode and vice versa.

7.1 T-grooVes

• There are three T grooves in the worktable. It is used to fix the work piece.

• There are two T grooves in the base, too. It is convenient for fixing the longer, heavier and larger working piece.

JS-834V or JS-840VB

A.min-1 or /min (R.P.M.) Indicator

B. Speed Control Switch

C. Fault light

D.Start Button

E. Emergency Stop Button(For CE)

F.Feed Depth Adjustment

G. Drill / Tap Switch

H. Stop Button

I. Cutting Liquid Control Switch

1. Check the power source

Push the start button to judge the motor and spindle shaft is in normal condition or not.

2. Spindle speed adjustment is controlled by the speed control switch. The speed will be

showed out in the electronic digital meter.

3. If it needs to stop urgently, just push the emergency stop switch.

4. Drill / Tap switch: For changing the machine to Drill Mode or Tap Mode.

3-2. Operation illustration and procedure:

1. There are three T grooves in the worktable. It is used to fix the work piece.

1-1.There are two T grooves in the base, too. It is convenient for fixing the longer, heavier and larger

working piece.

(Option)

2. These machines have special design for tapping, a quick change device. During tapping, if you

want spindle to turn reversely and withdraw tapping tip, just pull up grip handle only(as

JS-834V

A: Speed indicator

B: Speed control switch

C: Warning light

D: Start button

E: Emergency button

F: Feed depth adjustment

G: Drill/tap switch

H: Stop button

I: Control switch coolant liquid

Figure 5

JS-834V or JS-840VB

A.min-1 or /min (R.P.M.) Indicator

B. Speed Control Switch

C. Fault light

D.Start Button

E. Emergency Stop Button(For CE)

F.Feed Depth Adjustment

G. Drill / Tap Switch

H. Stop Button

I. Cutting Liquid Control Switch

1. Check the power source

Push the start button to judge the motor and spindle shaft is in normal condition or not.

2. Spindle speed adjustment is controlled by the speed control switch. The speed will be

showed out in the electronic digital meter.

3. If it needs to stop urgently, just push the emergency stop switch.

4. Drill / Tap switch: For changing the machine to Drill Mode or Tap Mode.

3-2. Operation illustration and procedure:

1. There are three T grooves in the worktable. It is used to fix the work piece.

1-1.There are two T grooves in the base, too. It is convenient for fixing the longer, heavier and larger

working piece.

(Option)

2. These machines have special design for tapping, a quick change device. During tapping, if you

want spindle to turn reversely and withdraw tapping tip, just pull up grip handle only(as

JS-834V

Figure 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Huvema HU 40 SUPER VARIO Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Huvema HU 40 SUPER VARIO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info