Bedienungsanleitung Hwam 2630 (Seite 8 von 36) (Englisch, Italienisch)

571924

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

If HWAM 2610/2620 is placed on a ﬂammable ﬂoor, always mount it on a plinth whether or not the

ﬂoor is covered by a non-ﬂammable material, such as a plate of glass or steel. The plinth is an accessory.

Contact your HWAM dealer for more information.

Drawing A HWAM 2610

HWAM 2630

HWAM 2610

HWAM 2630

1. Recommended for brick wall

10 cm 10 cm

For inﬂammable back wall

19 cm 19 cm

For inﬂammable side wall

36 cm 36 cm

To inﬂammable wall,corner installation

34 cm* 20 cm*

Distance to furnishings in front

80 cm 80 cm

*All dimensions in connection with corner installation are only recommendations. Contact your chimney

sweep for a clariﬁcation.

For wall-mounting, HWAM 2610/2620 must be placed at least 3 cm above any inﬂammable ﬂooring. This

also applies to any ﬂoorboard placed on the ﬂoor.

Remember to pay attention to any regulations concerning the required distance between

the wall and smoke pipe.

The distance to a brick wall is set to faciliate the servicing of the HWAM Autopilot IHS

. HWAM

2610/2620 may be mounted with wall ﬁttings only on a brick wall. The stove must be taken down when

the HWAM Autopilot IHS

is to be serviced.

Requirements for chimney and smoke pipe

The chimney must be of a sufﬁcient height to enable an adequate draft and to prevent smoke problems.

The stove requires a draft of at least 12 Pa.

The chimney must have a minimum opening equivalent to Ø 150 mm. The chimney opening should always

be at least the size of the outlet socket of the stove. The chimney must have an easily accessible soot door.

Smoke pipe and chimney must always be suitable for a stove connection. Ask your HWAM dealer for

more information.

Changing the smoke outlet from top outlet to rear outlet (drawing F)

1. Lift the cast-iron top (1) off the stove.

2. Remove the rear plate of the stove by loosening the two screws (2).

3. Remove the cover plate (3).

4. Remove the ﬂue ring (4) and fasten it to the rear of the stove.

5. Carefully fold the wires and fasten by pressing the metallic tabs (5).

6. Break off the cut-out (6) in the rear plate and fasten the rear plate to the stove again. Be careful not

to jam the wires when installing the rear plate.

7. Fasten the cover plate (3) to the top of the stove.

8. Place the cast-iron top (1) on the stove.

9. Place the cast-iron top cover (7) in the hole in the cast-iron top plate.

Connection to chimney

All the stoves have both rear and top smoke outlet that can be connected to an approved steel chimney on

top or directly out at the rear to a chimney.

Make sure that the chimney is tight and that no false draft is caused around neither the cover plate, in

connection with a covered smoke outlet, nor the cleanout door and pipe connections. Please note that

bent and/or horizontal smoke pipes will reduce the effect of the chimney draft.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam 2630 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam 2630

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info