Bedienungsanleitung Hwam 2640 (Seite 9 von 36) (Englisch, Italienisch)

571925

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Vertical cross-section of smoke ﬂue (Drawing B and C)

B: Top smoke outlet C: Rear smoke outlet

• Steel chimney (9).

• Flue gas elbow (10). Fits into smoke ﬂue socket.

• Brick-built jamb of ﬂue (11).

• Built-in pipe sleeve (12). Fits smoke ﬂue.

• Wall rosette (13). Covers disruption to wall around pipe sleeve.

• Joint (14). Sealed with packing material.

• Smoke outlets (15) of the HWAM stove.

• Smoke ﬂue regulating damper (16).

• Soot door (17).

Fitting the loose parts

Before the stove is installed, you must ensure that all loose parts are ﬁtted correctly.

Vertical cross-section of the stoves (Drawing B):

• The smoke shelf (5): Should rest on the rear plate and on the stand uppermost in the front of the

combustion chamber.

• The bafﬂe plate (6): Is suspended on two hooks, one in either side uppermost in the combustion chamber.

To mount the bafﬂe plate, lift it to a position at the very top of the combustion chamber, and then push

it back until it falls into place in the two hooks. When the stove is installed, the transport protection

(6a) is removed. Lift the smoke shelf up and forward. Then lower it and remove it from the combustion

chamber. Subsequently, the transport protection (6a) is bent downwards/forwards until it is vertical.

• The cast iron bottom plate (7): Must be in a ﬂat position at the bottom of the combustion chamber.

• Air grate (8). Place the accompanying air grate on the cast-iron bottom of the combustion chamber, as

far up front as possible and with the slats pointing backwards. The grate is positioned correctly when

grate and bottom slot together.

Connecting and preparing the HWAM Autopilot IHS

1. Connect the plug

a) to a normal 230V socket

b) to the Air box in the wood section underneath the combustion chamber (lead the plug through

the air slot at the bottom between the side and rear plates - on the left side of the wood-burning

stove when seen from the front. There is a mark on the Air box where the plug should be let in. See

the photo of the power supply on the Air box.

Air box without power supply Air box with power supply

2. Insert three AA batteries in the remote control. When the IHS logo disappears from the display, the

remote control is ready to use.

3. The remote control and the wood-burning stove must be connected (the factory will see to this).

If the status line at the bottom of the display is clear (empty) (

)and divided

into three sections, the wood-burning stove and the remote control are connected.

If the status line is dotted ( ), the remote control and the wood-burning stove

are not connected. Start with a display in which the light is off, and make the connection by pressing

and holding down the button, so the advanced menu is displayed. Then press the button repeatedly

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam 2640 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam 2640

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info