Bedienungsanleitung Hwam 3220 (Seite 13 von 44) (Englisch, Italienisch)

613740

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

12. Place the rear plate (1) on the guide pins at the back of the bottom plate of the stove; then press it

in towards the stove. Lift the rear plate and press it lightly inwards until it engages with the guide

pins.

Fitting the loose parts

Before the stove is installed, you must ensure that all loose parts are ﬁtted correctly.

Vertical cross-section of the stoves (Drawing B):

• The top plate of the stove (1)

• Rear smoke outlet (3). At the factory this is sealed with a cover plate. The smoke outlet is therefore

hidden behind the plate.

• Top smoke outlet (4)

• The smoke shelf (5). To be placed on top of the steel rail and on the holders in the sides.

• Two-piece smoke defector plate (6). Each half is hung on the hooks located beneath the top plate. The

two halves join in the holders behind the air pipe. Once the stove has been installed, twist the protection

off the two hooks by using pliers or a screwdriver.

• Removable rear plate (2). This must always be mounted if the stove is placed next to a combustible

wall

• Loose heat shield (8) under the ash pan. This can be used as a lid when the ash pan is removed for

emptying.

Connecting and preparing the HWAM Autopilot IHS

1. Connect the plug

a) to a normal 230V socket

b) to the Air box in the wood section underneath the combustion chamber (lead the plug through

the air slot at the bottom between the side and rear plates - on the left side of the wood-burning

stove when seen from the front. There is a mark on the Air box where the plug should be let in.

See the photo of the power supply on the Air box.

Air box without power supply Air box with power supply

2. Insert three AA batteries in the remote control. When the IHS logo disappears from the display,

the remote control is ready to use.

3. The remote control and the wood-burning stove must be connected (the factory will see to this).

If the status line at the bottom of the display is clear (empty) (

) and divided

into three sections, the wood-burning stove and the remote control are connected.

If the status line is dotted (

), the remote control and the wood-burning

stove are not connected. Start with a display in which the light is off, and make the connection by

pressing and holding down the button, so the advanced menu is displayed. Then press the button

repeatedly in short intervals until the text ”Link to stove” is highlighted and wait until it enters this

menu. Press the button in short intervals until the text “Connect” is highlighted and wait again.

When the text "Please cycle stove power" appears on the display, disconnect the electricity from

the Air box and then reconnect. Press the button once more. If the message "Connected to stove"

shows up in the display, the wood-burning stove and the remote control are connected. Press the

button once to return to the main menu. If you do not press the button again, the remote control

automatically leaves the menu and returns to the start display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam 3220 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam 3220

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info