Bedienungsanleitung Hwam 3220 (Seite 22 von 44) (Englisch, Italienisch)

613740

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Long burning times

You achieve the slowest combustion by setting the desired room temperature at level 0. At this level

the combustion takes place with the lowest possible ﬂue gas temperature and the ember phase will

be drawn out as long as possible.

How to achieve the best combustion

The HWAM Autopilot IHS

is purposely designed to generate the cleanest and the most economical

combustion. A good combustion is achieved when the ﬁre gets the right amount of oxygen supply at

the right time and place in the combustion chamber. The HWAM Autopilot IHS

allows for variations

in external circumstances. Nevertheless, it is important to use clean and dry wood (humidity approx.

16-18%). Read more on www.hwam.com.

Cleaning the glass

We recommend wiping the glass after a ﬁre. This is best done using a paper towel.

Types of fuel

The stove may be damaged by very high temperatures and the glass may turn white, for example. This

can be avoided by never allowing the stove to burn with the ashpan open and taking great care with

types of fuel that develop excessive heat, such as briquettes. If the ﬂue gas temperature exceeds 580

Celsius, the HWAM Autopilot IHS

will revert to safety adjustments and automatically turn down

the air valves to avoid overheating. When the temperature is reduced to 450

Celsius, the normal

functions apply again.

It is recommended that you use birch or beech wood that has been chopped and stored for at least

one year in an open shed exposed to sun and wind. The wood must be dry (max. 20% water contents)

before it is stored indoors. It is recommended that kindling wood is stored indoors for a couple of

days prior to use.

The stove is EN 13240 approved for ﬁring wood only. No particle board, lacquered, painted

or treated wood, plastics, or rubber may be burned.

MAintEnAncE

Cleaning

Any maintenance of the stove should only be carried out when it is cold. Daily maintenance is limited

to vacuum cleaning the stove externally, using the soft brush attachment. You can also dust the stove

using a dry, soft cloth or brush. But remember, only when the stove is cold. Do not use water, spirit

or any other kind of cleaner, as this will damage the lacquer.

Once a year, the stove should be thoroughly serviced. The combustion chamber should be cleared of

ashes and soot. The hinges and the closing hook must be greased with liquid copper fat spray (heat-

resistant up to 1100°C), see drawing G. Lift the door approx. ½ cm and spray copper fat onto the

hinge leaf.

Service inspection

Your stove should be given a thorough, preventive inspection once every two years. This includes:

• Thorough cleaning of the stove.

• Checking gaskets. Replace gaskets if they are not intact or have softened.

• Checking of heat insulating material and possibly replacement.

• Checking of the bottom/shaking grate.

• Lubricating the hinges and the locking hook with cobber grease (drawing G).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam 3220 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam 3220

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info