Bedienungsanleitung Hwam 3320 (Seite 50 von 60) (Englisch, Holländisch, Französisch, Italienisch, Spanisch)

613760

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

The chimney draught is created by the difference between the temperatures inside and outside the

chimney. The higher the temperature inside the chimney, the better the draught. It is therefore crucial

to properly warm up the chimney before closing the dampers and limiting the combustion in the stove

(a brick chimney takes longer to warm up than a steel chimney). On days where the weather and wind

conditions create insufﬁcient draught inside the chimney, it is even more important to warm up the

chimney as quickly as possible. The trick is to quickly get some ﬂames going. Split the wood into extra

ﬁne pieces, use an extra ﬁrelighter, etc.

If the stove has not been used for a longer period, it is important to check that the chimney pipe is

not blocked.

It is possible to connect several devices to the same chimney. However, it is important to ﬁrst check

the applicable rules.

Even a good chimney may work poorly if it is used incorrectly. Similarly, a bad chimney may work well

if used correctly.

Chimney sweeping

To prevent the risk of chimney ﬁres, the chimney must be cleaned every year. The ﬂue duct and the

smoke chamber above the bafﬂe plate must be cleaned together with the chimney. If the chimney is

too tall to be cleaned from above, it must be equipped with a soot door.

In case of a chimney ﬁre, close all dampers and call the ﬁreﬁghters. Before any further use, have the

chimney checked by the chimney sweeper.

Test results from nominal test EN 13240

Nominal heating effect 5.0 kW

Smoke temperature 264°C

Exhaust gas ﬂow 7.4 g/sec.

stokIng InstructIons - wood

The ﬁrst time you light up the stove, do it gently to allow all materials to acclimatise to the heat. The

lacquer used for the stove coating will harden the ﬁrst time the stove is lit. Therefore you should open

the door very gently, as otherwise there is a risk that the gasket will get stuck in the lacquer. Further-

more, the lacquer will give off some odours the ﬁrst time you light the stove. You should therefore

make sure that the room is properly ventilated. Please be aware that the glove supplied with the stove

could rub off the paint if the lacquer has not been allowed to harden sufﬁciently. Therefore you should

always be careful not to touch the door itself until the stove has been lit 2-3 times.

Tips about fuel

Approved fuel types

The wood burning stove is EN approved for combustion of wood only. It is recommended to use dried

chopped wood with a water content of a maximum of 20%. Stoking a ﬁre with wet wood results in

soot, environmental problems, and a less efﬁcient fuel economy.

Recommended wood types

All types of wood, for instance birch, beech, oak, elm, ash, conifers, and fruit trees can be used as fuel

in your wood burning stove. The great difference is not in the fuel value, but in the weight of the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam 3320 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam 3320

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info