Bedienungsanleitung Hwam 3620 (Seite 11 von 60) (Englisch)

571936

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Vertical cross-section of smoke ﬂue (Drawing C)

C1: Topsmokeoutlet C2:Rearsmokeoutlet

1. Steel chimney.

2. Flue gas elbow. Fits into smoke ﬂue socket.

3. Brick-built jamb of ﬂue.

4. Built-in pipe sleeve. Fits smoke ﬂue.

5. Wall rosette. Covers disruption to wall around pipe sleeve.

6. Joint. Sealed with packing material.

7. Smoke outlets of the HWAM stove.

8. Cover plate in the external rear plate – break off if a rear outlet is required.

9. Coverscrewedinposition:secureittothetopplatewithscrewsifarearoutletisrequired.

10. Smokebushing:tobescrewedtothebackofthestoveifarearoutletisrequired.

11. Adjusting damper in smoke pipe.

12. Cleaning hatch.

13. Smoke pipe to rear outlet.

14. Loosecastironcover:tobeplacedonthetopplatewhenthereisarearoutlet.

Connecting and preparing the HWAM Autopilot IHS

1. Connect the plug

a) to a normal 230V socket

b) to the Air box in the wood section underneath the combustion chamber (lead the plug through

the air slot at the bottom between the side and rear plates - on the left side of the wood-burning

stove when seen from the front. There is a mark on the Air box where the plug should be let in. See

the photo of the power supply on the Air box.

Air box withour power supply. Air box with power supply.

For the models HWAM 3610 and HWAM 3620 on pedestals, it is necessary to remove the front of

the pedestal in order to connect it to the power supply. To remove the front, follow the instructions

in the drawings D1-D3. Lead the plug through the rear of the pedestal and connect the power supply

to the Air box. Then replace the front of the pedestal.

2. Insert three AA batteries in the remote control. When the IHS logo disappears from the display, the

remote control is ready to use.

3. The remote control and the wood-burning stove must be connected (the factory will see to this).

If the status line at the bottom of the display is clear (empty) (

)and divided

into three sections, the wood-burning stove and the remote control are connected.

If the status line is dotted ( ), the remote control and the wood-burning stove

are not connected. Start with a display in which the light is off, and make the connection by pressing

and holding down the button, so the advanced menu is displayed. Then press the button repeatedly in

short intervals until the text ”Link to stove” is highlighted and wait until it enters this menu. Press the

button in short intervals until the text “Connect” is highlighted and wait again. When the text "Please

cycle stove power" appears on the display, disconnect the electricity from the Air box and then recon-

nect. Press the button once more. If the message "Connected to stove" shows up in the display, the

wood-burning stove and the remote control are connected. Press the button once to return to the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam 3620 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam 3620

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info