Bedienungsanleitung Hwam 3740 (Seite 11 von 20) (Englisch)

744526

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Page 11 of 20 pages

Model Weight Height Width Depth

HWAM 3740c/3740m: 104/101 kg 102.5 cm 49.9 cm 37.5 cm

HWAM 3760c/3760m: 117/113 kg

125.4 cm

49.9 cm 37.5 cm

Heat storing slabs, HWAM 3760 32 kg

The stove is mainly made of sheet iron, with some items made of cast iron.

Floor plate

European, national and local regulations must be observed in terms of the size and thickness of a non-

combustible ﬂoor covering the ﬂoor in front of the combustion chamber opening. Ask your HWAM

retailer for assistance. The combustion chamber opening is 34.0 cm wide.

Distance to inﬂammable materials

Your HWAM woodburning stove should always be installed on a non-combustible hearth. If it is installed

on a wooden ﬂoor or similar, the ﬂoor must be covered with a non-combustible material.

HWAM 3740, HWAM 3760 (Drawing A)

1. Recommended for brick wall

10 cm

For inﬂammable back wall

10 cm

For inﬂammable side wall

35 cm

To inﬂammable wall,corner installation

9 cm

Distance to furnishings in front

90 cm

Remember to pay attention to applicable regulations concerning the required distance

between the wall and smoke pipe.

The distance to a brick wall is set to faciliate the servicing of the HWAM

Autopilot™ system.

Please be aware that not all glass parts are heat-resistant. For this reason, a glass wall should sometimes

be treated as a ﬂammable wall, in which case we ask you to contact your local chimney sweep or glass

producer to hear at what distance the stove should be kept from glass.

Requirements for chimney and smoke pipe

The chimney must be of a sufﬁcient height to enable an adequate draft and to prevent smoke problems.

The stove requires a draft of at least 12 Pa.

The chimney must have a minimum opening equivalent to Ø 150 mm. The chimney opening should always

be at least the size of the outlet socket of the stove. The chimney must have an easily accessible soot door.

Smoke pipe and chimney must always be suitable for a stove connection. Ask your HWAM dealer for

more information.

Changing the smoke outlet from top outlet to rear outlet - HWAM 3740 (drawing I)

If a wood-burning stove from the factory is supplied with a top outlet but you want to change it to a

rear outlet, this can be done by following the instructions below. If this change is made, a closed top plate

without a hole for the top outlet can be purchased.

1. Removing the external heat shield (1). Lift the heat shield (1) up and remove it from the stove. The

heat shield has a cut-out for the ﬂue duct. Break off the pre-cut plate (2); the resulting hole ﬁts the

ﬂue duct.

2. Removing the rear plate (3). Lift the rear plate and pull it away from the stove so that it disengages

from the guide pins (4) on the bottom plate of the stove. There is a cut-out in the rear plate for the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam 3740 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam 3740

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info