Bedienungsanleitung Hwam 4640 (Seite 39 von 48) (Englisch, Dänisch, Schwedisch, Norwegisch)

613742

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Min. distances - uninsulated ue gas pipe:

(drawing A)

HWAM 4600

with steel cladding

HWAM 4600

with stone cladding

1. Recommended for brick wall, back, cm

10 10

Recommended for brick wall, side, cm

10 10

For inammable wall, back, cm

20 20

For inammable wall, side, cm

35 45

To inammable wall, corner installation, cm

12 15

Distance to furnishings in front, cm

130 140

Min. distances - insulated ue gas pipe:

(drawing A)

HWAM 4600

with steel cladding

HWAM 4600

with stone cladding

1. Recommended for brick wall, back, cm

7* 7*

Recommended for brick wall, side, cm

7* 7*

For inammable wall, back, cm

7* 7*

For inammable wall, side, cm

40 45

To inammable wall, corner installation, cm

12 15

Distance to furnishings in front, cm

130 140

*We recommend 10 cm to facilitate service on HWAM Autopilot.

Please be aware that not all glass parts are heat-resistant. For this reason, a glass wall should sometimes

be treated as a ammable wall, in which case we ask you to contact your local chimney sweep or glass

producer to hear at what distance the stove should be kept from glass.

Take note of the applicable regulations for the distance between the wall and ue pipe.

The distance to a brick wall is set to faciliate the servicing of the Autopilots system.

Requirements for chimney and smoke pipe

The chimney must be of a sufcient height to enable an adequate draft and to prevent smoke problems. The

stove requires a draft of at least 12 Pa.

The chimney must have a minimum opening equivalent to Ø 15 cm. The chimney opening should always

be at least the size of the outlet socket of the stove. The chimney must have an easily accessible soot door.

Smoke pipe and chimney must always be suitable for a stove connection. Ask your HWAM dealer for more

information.

Changing the ue outlet from a top outlet to a rear outlet (drawing H)

Steps 1 and 12 only apply to the HWAM 4660 and HWAM 4680 models.

1. Remove the heat storage area front (1) by lifting the front and pulling away from the stove.

2. Lift the top plate (2) off the stove.

3. Remove the rear plate (3) by loosening the two screws (4). The rear plate has a cut-out for the ue

pipe. Cut out the plate (5) within this cut-out.

4. The heat shield has a cut-out for the ue pipe. Cut out the plate (6) within this cut-out.

5. Remove the cover plate (7) on the rear of the stove (behind the cut-out plate in the heat shield) by

removing the three screws (8).

6. Remove the smoke ring (9) above the combustion chamber by removing the three screws (10).

7. Place the smoke ring (9) in front of the ue outlet hole on the rear of the stove and afx using the

three screws (10).

8. Place the cover plate (7) so that it closes the ue outlet on top of the combustion chamber (where

the smoke ring was just removed) and afx using the three screws (8).

9. Place the rear plate (3) on the guide taps (11) on the rear side of the stove's base plate and afx the

rear plate using the two top screws (4).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam 4640 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam 4640

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info