Bedienungsanleitung Hwam 7100 (Seite 18 von 52) (Englisch)

613745

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

In exceptional cases the system might not register that the stove has been re-stoked. This can occur if

the oxygen level in the combustion compartment, due to the low ﬂue gas temperature, reaches a point

where the system fails to register an increase in the oxygen level in spite of the stove door having been

opened. After stoking, the status line should therefore be checked on the remote control. Shortly after

the lighting of the wood, the middle section of the remote control, representing the combustion process

phase, should light up. (

) If it enters standby mode, press the remote control

twice, so the match symbol is displayed.

During combustion, the outer surfaces of the stove will become hot, and due care must

therefore be shown. Please note that the handle on the pull-out drawer also gets very warm.

Always remember to wear gloves when operating the drawer while the stove is in use.

Firing with coal, briquettes and coke

Burning coal and coke is not possible in this stove since there is no room for a coal insert. Briquettes can

be used however. These are placed onto the wood embers. Remember that after this the regulat-

ing rod must be closed again. Be aware that using fuels other than wood, will cause soot to

form on the glass pane.

FiRing in gEnERAl

Rapid or ﬁerce heat

Rapidorerceheatisobtainedbyburningmanysmallpiecesofwood.

Maximum amounts of fuel:

Themaximumallowedamountoffuelperhouris:

Wood:2.4kg

If these limits are exceeded, the stove will no longer be covered by the factory guarantee, and it may also

become damaged due to excessive heat. The stove has been approved for intermittent use.

Typical re-ﬁring interval

Typical re-ﬁring interval at nominal performance

Wood:65min

Long burning times

You achieve the slowest combustion by setting the desired room temperature at level 0. At this level

the combustion takes place with the lowest possible ﬂue gas temperature and the ember phase will be

drawn out as long as possible.

How to achieve the best combustion

The HWAM Autopilot IHS

is purposely designed to generate the cleanest and the most economical

combustion. A good combustion is achieved when the ﬁre gets the right amount of oxygen supply at the

right time and place in the combustion chamber. The HWAM Autopilot IHS

allows for variations in

external circumstances. Nevertheless, it is important to use clean and dry wood (humidity approx. 16-20%).

Cleaning the glass

We recommend wiping the glass after a ﬁre. This is best done using a paper towel.

Types of fuel

The stove may be damaged by very high temperatures and the glass may turn white, for example. This can

be avoided by never allowing the stove to burn with the ashpan open and taking great care with types

of fuel that develop excessive heat, such as briquettes. If the ﬂue gas temperature exceeds 580

C, the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam 7100 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam 7100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info