Bedienungsanleitung Hwam I 30-55 (Seite 7 von 56) (Englisch, Holländisch, Französisch, Italienisch, Spanisch)

571930

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Chimney

The chimney is the “motor” of the insert and it is crucial for the functioning of the woodburning insert.

The chimney draft provides a partial vacuum in the insert. This vacuum removes the smoke from the

insert, sucks air through the dampers for the so-called glass pane rinse which keeps the glass free of soot,

and sucks in air through both primary and secondary dampers for the combustion.

The chimney draft is created by the differences in temperature inside and outside the chimney. The

higher the temperature within the chimney, the better the draft. It is crucial, therefore, that the chimney

is warmed through properly before closing the damper and limiting the combustion in the insert (a brick

chimney takes longer to warm through than a steel chimney).

On days where the weather and wind conditions create insufﬁcient draught inside the chimney, it is even

more important to warm up the chimney as quickly as possible. The trick is to quickly get some ﬂames

going. Split the wood into extra ﬁne pieces, use an extra ﬁrelighter, etc.

If the stove has not been used for a longer period, it is important to check that the chimney pipe is not

blocked.

It is possible to connect several devices to the same chimney. However, it is important to ﬁrst check the

applicable rules. Contact your local chimney sweeper for the approval of your chimney.

Even a good chimney can function badly if it is not used correctly. Similarly, a bad chimney may function

well if it is used correctly.

Chimney sweeping

To prevent the risk of chimney ﬁres, the chimney must be cleaned every year. The ﬂue duct and the smoke

chamber above the bafﬂe plate must be cleaned together with the chimney. If the chimney’s height makes

cleaning from above impossible, a cleaning hatch must be installed in the chimney.

In case of a chimney ﬁre, close all dampers and call the ﬁreﬁghters. Before any further use, have the

chimney checked by the chimney sweeper.

mountIng and connEctIon (drawIng a)

The HWAM I 30/55 consists of a moveable, external brickwork casing, as well as an insert that is pushed

into place and connected once the brickwork casing has been assembled.

The HWAM I 30/55 can be connected in two ways:

1. Mounting and connecting in an existing ﬁreplace.

2. New construction around the insert, possibly including heat ducts to other rooms.

1. Mounting and connecting in an existing ﬁreplace (Drawing A1-A3).

Before mounting the insert in a brick-built ﬁreplace, the regulating damper in the existing chimney must

be removed and the smoke neck, if any, should be widened so that the ﬁre tube from the insert can be

connected directly to the chimney. Any bricks positioned on edge at the bottom of the ﬁreplace should

also be removed.

In advance, decide with a specialist or the chimney sweep where a soot door (1) should be placed, so

that the ﬁre tube can be cleaned from above while the door of the insert remains closed.

Mounting the smoke pipe (Drawing A1)

First mount the joining ﬂange (2) with a suitable length of ﬁre tubing or ﬂexible tubing (3). Push the

inner pipe into the connector. The inner pipe must be turned so that the handle goes as far as possible

into the connector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam I 30-55 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam I 30-55

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info