Bedienungsanleitung Hwam I 30-55 (Seite 12 von 56) (Englisch, Holländisch, Französisch, Italienisch, Spanisch)

571930

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

creates inefﬁcient combustion and a modest effect.

• Don’t savour the ﬁre during night time

We advise against adding ﬁre wood to your stove and reducing the air supply at night in an attempt to

still have some embers left in the morning. If you do so, large amounts of hazardous smoke will be emitted,

and your chimney will be exposed to unnecessarily large amounts of soot with the risk of a chimney ﬁre.

clEanIng

External cleaning

Cleaning of the insert should only be performed when it is not in use/cool. Daily maintenance is limited

to a minimum. It is easiest to vacuum the outside of the insert with a tiny nozzle with soft brushes.

Cleaning the glass (drawing G)

If it becomes necessary to clean the inside of the glass pane, lift the door halfway up and pull out the

two top guide latches (1) on each side of the door in order to loosen them from the screws (2). The

glass scan then be tilted out and cleaned. Once the glass is clean, lift the door again halfway up, pull out

the top guide latches on the sides, ease the glass pane into place, and lead the guide latches back into

place over the screws.

The inside of the glass pane is best cleaned with damp paper towel dipped in ash. Afterwards, dry with

a clean paper towel.

The outside of the glass can be cleaned with ordinary cleaning solvent used to polish surfaces. We recom-

mend wiping down the window pane when the insert is not in use/cool.

Ash

We recommend removing ash from the combustion chamber with an ash suction device.

Ash can be disposed of through daily refuse collection. Be aware that embers in the ash can

remain hot up to 24 hours after the ﬁre in the insert has gone out!

maIntEnancE

Maintenance

Regularly ensure that the air slit for the pane air rinse function (drawing C, 3) is free of ash and soot

particles. Regularly check to make sure that seals in the door are complete and soft. If not, they should

be replaced. Use only original spare parts.

The insert should be thoroughly cleaned once a year. Ash and soot must be removed from the combus-

tion chamber. If necessary, lubricate the door lift mechanism with copper grease.

Service inspection

At least once every other year, the insert should receive a thorough, preventative service inspection.

Among other things, the service inspection covers:

• A thorough cleaning of the insert.

• Inspection of the door lift mechanism and lubrication with copper grease if necessary (drawing B,1).

• Check the spring in the automatic unit and replace if necessary.

• Checking gaskets. Replace gaskets if they are not intact or are no longer soft.

• Inspection of springs for chain drive. Inspection to ensure that the chain drive is equal on both sides,

and that the door closes tightly all the way around.

• Inspection/possible replacement of heat insulation material.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam I 30-55 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam I 30-55

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info