Bedienungsanleitung Hwam I45 (Seite 49 von 60) (Deutsch, Englisch, Dänisch, Schwedisch, Norwegisch)

571929

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

InstallatIon Manual

Legislation

If the insert is to be mounted in a newly built, non-approved open ﬁreplace, all legal requirements and

local building regulations must be observed. It would always be advantageous to consult your chimney

sweep before mounting the insert.

Room requirements

There must be a constant supply of fresh air to the room in which the

insert is to be installed. A window

that opens or an adjustable air vent should sufﬁce.

Please be aware that not all glass parts are heat-resistant. For this reason, a glass wall should sometimes

be treated as a ﬂammable wall, in which case we ask you to contact your local chimney sweep or glass

producer to hear at what distance the insert should be kept from glass.

Distance to inﬂammable materials

Please refer to local building regulations to determine the size of the ﬁreproof area in front of the ﬁreplace.

The insert must be positioned at least 30 cm above the ﬂoor if the ﬂoor is made of ﬂammable material.

If there is inﬂammable material around the outer casing, non-inﬂammable insulation (Fire Batts) is required

between the casing and the inﬂammable material. The insulation must be 60 mm thick on both sides of

and behind the casing and 40 mm thick beneath the bottom of the casing. The requirement for insulation

above the top of the casing is 140 mm. The thermal conductivity of the insulation must be less than 0.09

W/m x K (as measured at 200 ºC); i.e., thermal conductivity must be lower than 0.09 W/m x K.

Chimney requirements

The chimney must be of a sufﬁcient height to enable an adequate draft and to prevent smoke problems.

Nominal draft: approx. 12 Pa.

The chimney must have a minimum opening equivalent to Ø 150 mm.

The chimney opening should always be at least the size of the outlet socket of the insert.

The chimney must have an easily accessible soot door.

Chimney

The chimney is the “motor” of the insert and it is crucial for the functioning of the woodburning insert.

The chimney draft provides a partial vacuum in the insert. This vacuum removes the smoke from the

insert, sucks air through the dampers for the so-called glass pane rinse which keeps the glass free of soot,

and sucks in air through both primary and secondary dampers for the combustion.

The chimney draft is created by the differences in temperature inside and outside the chimney. The

higher the temperature within the chimney, the better the draft. It is crucial, therefore, that the chimney

is warmed through properly before closing the damper and limiting the combustion in the insert (a brick

chimney takes longer to warm through than a steel chimney).

On days where the weather and wind conditions create insufﬁcient draught inside the chimney, it is even

more important to warm up the chimney as quickly as possible. The trick is to quickly get some ﬂames

going. Split the wood into extra ﬁne pieces, use an extra ﬁrelighter, etc.

If the stove has not been used for a longer period, it is important to check that the chimney pipe is not

blocked.

englIsh

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam I45 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info