Bedienungsanleitung Hyundai 56477 (Seite 7 von 19) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

675879

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

HYUNDAI

12 13

ENGLISH

screws or electrical boxes as they may damage the sanding

plate.

Emptying the dust bag

The dust bag must be emptied and cleaned regularly. Empty the

dust bag when it is half full and also clean the inside. Regular

emptying and cleaning of the dust bag is important. Due to lack of

maintenance, the suction power will decrease. The dust will then

come out through the sanding disc instead of being sucked into the

bag.

• Turn off and disconnect the tool from the power supply.

• The bag has a seam sealed by a plastic clip. Open the plastic

clip and empty the dustbag.

• Clean the bag and close it.

CLEANING AND MAINTENANCE

The machine does not require any special maintenance.

• Regularly clean the ventilation slots.

Before performing maintenance to the machine, always

unplug the machine.

TECHNICAL DATA 56477

Mains voltage V 230-240

Mains frequency Hz 50

Power input W 750

No load speed min

-1

1000-1850

Diameter sanding plate mm 225

Weight kg 4,3

NOISE AND VIBRATION

Typically the A-weighted sound pressure level of the machine is

83.1 dB(A). Uncertainty K = 3 dB(A).

The noise level when working can exceed 94.1 dB(A).

Wear hearing protection!

Vibration emission value a

= 1.171 m/s

Uncertainty K = 1.5 m/s

The declared vibration total value was measured by a standard

test method and may be used for comparing one tool with another.

The declared total vibration value can also be used in a preliminary

exposure estimate .

Warning

The vibration emission during actual use of the machine

tool can differ from the declared value depending on the

way the tool is used.

Identifying the safety measures to protect the operator

is essential, these are based on an exposure estimation

in the actual conditions of use (considering all operating

cycle parts such as the times when the tool is on and off

and when it’s running as well as its starting time).

Changing the brush

• Remove abrasive pad (see “Assembly and changing of the

abrasive discs”).

• Use a Phillips screwdriver to remove the six retaining screws

• Then remove the brush.

• Place the new brush in the housing and install it using the six

retaining screws.

• Replace the abrasive pad.

USE

Wear a protective mask. Harmful and toxic dust may be

produced when using the sander. This dust can interfere

dangerously with your and others health. Kindly always

wear a protection mask against dust when using this

product. Keep people and animals away from the work

area when the device is running.

The sander has a special sanding head: the head can rotate in

multiple directions, allowing the abrasive pad to adjust to the work

surface. This enables the user to sand the top, middle and bottom of

a wall or ceiling joint without changing its position.

How to hold the sander

The sander should be held with both hands on the main tube.

The hands may be placed anywhere along the main tube for best

application.

Keep the hands on the main tube. Do not place the hands

in the area around the sanding head. The sanding head

swivels in multiple directions and could jam your hand.

Starting and stopping

Always check that the power supply corresponds to the

voltage on the rating plate and that the sander switch is

OFF.

• Plug it into the socket

• Press and hold the on/off switch (2) to switch on the machine.

When you release the on/off switch, the machine is switched off.

You can lock the on/off switch by pressing the on/off switch and

then the lock button (3). The switch lock can be released by

pressing the on/off switch.

Speed adjustment

This sander is equipped with adjustable speed. The speed can be

controlled with the speed control (1). A higher speed should be used

for leveling and removal. A lower speed can be used for precise

renement.

Sanding

Place the correct sanding disc for the surface to be sanded (ceiling,

corner of the ceiling, different parts of a wall).

When sanding a wall or ceiling, use a ladder to reach the area to be

scoured.

Sanding tips

• Place the sander against the working surface with suitable

strength.

• Apply additional pressure for a stronger removal and reduce the

pressure for a smoother and more accurate finish.

• Apply enough pressure to keep the sanding plate flat against the

wall surface. However, excessive pressure can cause rubbing

marks or even irregularities on the worked surface.

• Keep the sander in constant motion while holding the sanding

plate in contact with the surface to be sanded.

• Use a steady, stable sweeping motion, balancing strength well.

Irregular movements and even stopping on the working surface

may create traces and irregularities.

• Avoid moving the sanding plate against objects, such as nails,

GUARANTEE

Refer to the enclosed guarantee conditions for the terms and

conditions of guarantee.

ENVIRONMENT

Disposal

Your product, accessories and packaging should be sorted for

environmental-friendly recycling.

Only for EC countries

Do not dispose of power tools into domestic waste. According to the

European Guideline 2002/96/EC for Waste Electrical and Electronic

Equipment and its implementation into national right, power tools

that are no longer usable must be collected separately and disposed

of in an environmentally friendly way.

Subject to change; specications can be changed without further

notice.

Hyundai 56477 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info