Bedienungsanleitung Hyundai 56551 (Seite 8 von 20) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

675869

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

HYUNDAI

Switching off

• Set the on/off switch to position ‘I’ and let it run

for a few minutes.

• Then set the on/off switch to position ‘0’.

• Let the tool cool down before moving or

storing it.

Immediately switch off the appliance when

• Plug and/or cable are defective or damaged.

• The switch is defective.

• You smell or see smoke caused by scorched

insulation from the hot air gun.

When the temperature is excess

600° C, the heats switches it off

automatically, however, the heater

continues to run. When the heater has

cooled to operating temperature, the

heater is switched on again.

Use of accessories (fig. B)

Fishtail nozzle (6)

Deflects air away from glass for

example when stripping paint in

window frames or softening putty.

Reduction nozzle (7)

Distributes air equally over small

areas.

Stationary use

This tool can also be used in stationary mode.

• Unfold the hang hook and place the tool onto

the workbench.

• Secure the cable to prevent pulling the tool off

the workbench.

• Carefully switch the tool on.

Make sure that the nozzle always

points away from you and any

bystanders. Make sure not to drop

anything into the nozzle.

Troubleshooting

In case the hot air gun does not work well, we

give you subjoined some possible causes and

their solutions.

The engine gets overheated

The ventilation slots of the hot air gun are dirty.

Clean the ventilation slots.

PACKAGE CONTENTS

The package contains the following parts:

Hot-air gun

Reduction nozzle

Fishtail nozzle

Manual

Safety warnings

Guarantee and service

DESCRIPTION (FIG. A)

Your hot-air gun has been designed for the

following operations:

- removing paint and paint residues from wood,

metal and synthetics;

- removing self-adhesive labels;

- applying PVC labels;

- moulding low-temperature materials, including

acrylics and perspex;

- melting together synthetics, including materials

and foils with a PVC layer;

- shrinktubing;

- heating pipe attachments and bowing pipes;

- repairing skis, surf boards and similar sporting

equipment.

1. On/off switch

2. Air flow outlet

3. Handle

4. Ventilation opening

5. Hang hook

6. Reduction nozzle

7. Fishtail nozzle

Instructions for use

• Aim the mouthpiece of the machine at the

workpiece.

• Heat the material a few seconds before

working it.

• If required set a higher or lower level

temperature by opening or closing the

ventilation opening.

• For optimum result it is recommended to test

the machine first on a small part of the

workpiece.

Switching on (fig. A)

The tool can be switched on to two different

temperature settings.

• To switch the machine on to the low setting,

set the on/off switch (1) to ‘I’.

• To switch the machine on to the high setting,

set the on/off switch to ‘II’.

• Some smoke may be emitted after switching

on; this does not indicate a problem.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hyundai 56551 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info