Bedienungsanleitung Hyundai 57014 - HYM51SPE (Seite 28 von 36) (Englisch)

675899

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

7. TROUBLESHOOTING.

7.1. Engine troubleshooting – where necessary

all corrective actions should be carried out by

suitably qualified persons.

7.2. If the starter rope becomes disconnected

from the rope guide on handle, disconnect the

spark plug cap. Depress the blade control

handle and pull the starter rope out from

engine slowly and re- engage in guide. Re

connect spark plug cap.

PROBLEM – ENGINE DOES NOT START.

ENGINE DIFFICULT TO START OR LOSES POWER.

Possible causes;

1. Dirt, water or stale fuel in tank.

2. Vent hole in fuel tank cap is plugged.

3. Air filter element is dirty.

Possible corrective actions;

1. Drain fuel and clean tank. Fill tank with clean,

fresh fuel.

2. Clean or replace fuel tank cap.

3. Clean air filter element.

ENGINE DOES NOT START ON BATTERY.

Possible causes;

1. Operator Presence Control (OPC) lever not

operated.

2. Battery discharged.

3. Blown fuse. Fuse rating 30 amp blade fuse

Possible corrective actions;

1. Hold the OPC lever towards the main handle

at the same time turn the start key in a

clockwise direction (against spring tension).

2. Charge battery.

3. Open battery housing, check and replace

fuse.

ENGINE OPERATES ERRACTICALLY.

Possible causes;

1. Spark plug is defective.

2. Spark plug gap is incorrect.

3. Air filter element is dirty.

Possible corrective actions;

1. Fit new, correctly gapped plug.

2. Set gap between electrodes at

0.7 to 0.8mm.

3. Clean air filter element.

Page 28

Revision 5 - August 2016

Troubleshooting video guides can be found on

You Tube - please follow link on our website -

http://hyundaipowerequipment.co.uk

Whilst carrying out troubleshooting/

maintenance you must wear appropriate

Personal Protective Equipment (PPE) when using

this machine. Suggested PPE Sturdy footwear,

work gloves (especially when working near

blade), long trousers and hearing protection. To

prevent unwanted starting unplug the HT lead,

for some operations it will be necessary to

remove all fuel/oils.

Possible causes;

1. Throttle lever not in the correct position for

the prevailing conditions.

2. Fuel tank is empty.

3. Stale fuel

4. Air filter element is dirty.

5 .Spark plug is loose.

6. Spark plug cap loose or disconnected from

plug.

7. Spark plug gap is incorrect.

8. Carburetor is flooded with fuel.

9. Faulty ignition module.

10. Loose Operator Prescence Control cable.

Possible corrective actions;

1. Move throttle lever to correct position.

2. Fill tank with fuel.

3. Drain carburetor float bowl.

4. Clean air filter element.

5. Tighten spark plug to 25- 30Nm.

6. Make sure spark plug cap is correctly fitted

onto spark plug.

7. Set gap between electrodes at

0.7 to 0.8mm.

8. Remove air filter element and pull starter

rope continuously until carburetor clears.

9. Contact the service dealer.

10. Loose Operator Prescence Control cable.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hyundai 57014 - HYM51SPE Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info