Bedienungsanleitung Hyundai 57381 - HYCH1500E-2 (Seite 35 von 40) (Englisch)

675905

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Issue

Possible causes

Possible corrective actions

STARTING DIFFICULTY

NORMAL SPARK

ISSUE WITH FUEL SYSTEM

Poor fuel supply.

No fuel in fuel system, fuel tap

closed.

Fuel cap air vent blocked.

Fuel tap blocked.

Fuel supply normal.

Dirty or stale fuel.

Water in fuel.

Incorrect fuel.

Poor fuel supply.

Fill with fuel – open fuel tap.

Clear blocked air vent.

Clear blockage.

Fuel supply normal.

4, 5 & 6. Clear fuel from system and

refill with fresh fuel.

STARTING DIFFICULTY

NORMAL FUEL

ISSUE HT LEAD/SPARK PLUG

Normal spark from HT lead.

Carbon build up on spark plug.

Electrodes badly burnt/damaged.

Incorrect spark plug gap.

No spark at HT lead.

HT lead damaged.

Ignition coil damaged.

Gap between ignition coil and

flywheel to big.

Normal spark from HT lead.

Clean carbon build up.

Replace spark plug.

Adjust the spark plug gap.

No spark at HT lead.

Replace HT lead.

Replace Ignition coil.

Adjust gap.

STARTING DIFFICULTY

(ELECTRIC)

Battery connection.

Loose or incorrect battery

connections.

Battery not charged.

Battery connection.

Check polarity and tighten

connections.

Remove battery from machine and

recharge.

MACHINE’S WHEELS TRACK LEFT

OR RIGHT WHILE BEING TOWED

1. Low tyre pressures. 1. Inflate tyres.

THE SHREDDER DOES NOT

SHRED PROPERLY. THE WOOD IS

NOT PULLED INTO THE MACHINE

BY ITSELF.

THE CHIPS DO NOT HAVE THE

SAME SIZE.

The blades are worn too much.

The diameter of the branches in-

serted into the machine are larger

than 100 mm for HYCH1500E-2 or

70mm for HYCH7070[E]-2

The gap between the fixed blade

and the counter-blade is too large,

the correct gap is ½ mm

Change or sharpen the blades and

counter-blade.

Note that the blades are sharpened

on both edges so they can be re-

versed.

Shut the engine off and remove the

branch that is too thick.

Adjust the gap between the blade

and the counter-blade in the slots

THE ENGINE WILL NOT START OR

TURN BECAUSE THE ROTOR IS

JAMMED.

1. The diameter of branches is too

big. There are unacceptable materials

such as stones or metal in the input

tube. A length of branch remains in

the rotor after the engine was last

stopped.

Shut off the engine, remove the spark

plug cap. NEVER under any circum-

stances use your hands to remove

stuck wood.

Reduce size of wood to 100 mm for

HYCH1500E-2 or 70mm for HY-

CH7070[E]-2 or less.

Use a piece of wood to turn the rotor

to remove the material from the rotor

and input tube. If necessary, remove

the cap of the bearing housing and

rotate the rotor axle with a spanner.

If necessary, remove the input or out-

put tube to get access to the rotor.

Check the sharpness of all blades,

have them sharpened or replace as

required.

Make sure all blade bolts are properly

tightened.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hyundai 57381 - HYCH1500E-2 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info