Bedienungsanleitung Hyundai 57504 (Seite 7 von 15) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

675848

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

HYUNDAI

12 13

FRANÇAIS

Cleaning the inlet filter

Before use always check the inlet filter and clean

it if necessary.

• Use your fingers to remove the filter from the

connection. Beware not to damage the filter.

• Use your fingers to re-install the filter.

• Check whether the filter has been placed into

the connection correctly.

Cleaning the nozzle (fig. F)

During use, if the water jet decreases or stops, the

nozzle needs to be cleaned.

• Make sure that the machine is switched off

and that the tap of the water mains has been

closed.

• Use the pricking tool (16) provided, to clean

the opening (17) in the nozzle (9).

TECHNICAL DATA 57504

Mains voltage V 230

Mains frequency Hz 50

Power input W 1,600

Operating pressure bar 90

Max. operating pressure bar 135

Water consumption l/min 5.5

Max. pressure water supply bar 4

Max. water temperature °C 50

Weight kg 8.5

GUARANTEE

Refer to the enclosed guarantee conditions for the

terms and conditions of guarantee.

ENVIRONMENT

Disposal

Your product, accessories and packaging should

be sorted for environmental-friendly recycling.

Do not dispose of power tools into domestic

waste. According to the European Guideline

2002/96/EC for Waste Electrical and Electronic

Equipment and its implementation into national

right, power tools that are no longer usable must

be collected separately and disposed of in an

environmentally friendly way.

Subject to change; specifications can be changed

without further notice.

POSSIBLE PROBLEMS AND SOLUTIONS

Symptom Possible causes Corrective actions

No detergent 1. Soap holder is clogged 1. Clean soap holder with warm

water

2. Replace soap holder

Unit begins to smoke 1. Overheated, overloaded or

damaged motor

1. Turn off unit and call the

dealer

Pressure cleaner does not start

1. Unit is pressurized

2. Plug is not well connected or

electric socket is faulty

3. Extension cord is too long or

wire size too small

4. Main voltage supply is too low

5. Thermal safety switch has

tripped

1. Squeeze trigger on gun

2. Check plug, socket and fuse

3. Remove extension cord

4. Check that main supply

voltage age is adequate

5. Switch off unit and allow

motor to cool down

Pump does not reach necessary

pressure

1. Water inlet filter is clogged

2. Pump is sucking air from

hose connections

3. Nozzle is worn or not correct

size

4. Unloader is clogged or worn

5. Valves is clogged or worn

1. Clean water inlet lter

2. Check that connections and

locking ring are properly

tightened

3. Call the dealer

4. Call the dealer

5. Call the dealer

Fluctuating pressure 1. Pump is sucking air

2. Clogged nozzle

3. Valves dirty, worm or stuck

4. Water seals worn

1. Check that hoses and

connections are tight

2. Clean with pricking tool

3. Call the dealer

4. Call the dealer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hyundai 57504 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info