Bedienungsanleitung Hyundai Atos 2002 (Seite 216 von 249) (Englisch)

664918

216

Zoom out

Zoom in

Vorherige Seite

1/249

Nächste Seite

VEHICLE MAINTENANCE REQUIREMENTS

5-5

F060A01A-AAT

EXPLANATION OF SCHEDULED MAIN-

TENANCE ITEMS

F060M01A-AAT

o Engine oil and filter

The engine oil and filter should be changed at

the intervals specified in the maintenance sched-

ule. If the car is being driven in severe condi-

tions, more frequent oil and filter changes are

required.

F060B01A-AAT

o Drive belts

Inspect all drive belts for evidence of cuts,

cracks, excessive wear or oil saturation and

replace if necessary. Drive belts should be

checked periodically for proper tension and

adjusted as necessary.

F060C01A-AAT

o Fuel filter

A clogged filter can limit the speed at which the

vehicle may be driven, damage the emission

system and cause hard starting. If an exces-

sive amount of foreign matter accumulates in

the fuel tank, the filter may require replacement

more frequently.

After installing a new filter, run the engine for

several minutes, and check for leaks at the

connections.

F060D01A-AAT

o Fuel lines, fuel hoses and connec-

tions

Check the fuel lines, fuel hoses and connec-

tions for leakage and damage. Replace any

damaged or leaking parts immediately.

F060E01A-AAT

o Timing belt

Inspect all parts related to the timing belt for

damage and deformation. Replace any dam-

aged parts immediately.

F060G01A-AAT

o Vapour hose and fuel filler cap

The vapor hose and fuel filler cap should be

inspected at those intervals specified in the

maintenance schedule. Make sure that a new

vapour hose or fuel filler cap is correctly re-

placed.

F060F01A-AAT

o Vacuum, crankcase

ventilation hoses

Inspect the surface of hoses for evidence of

heat and/or mechanical damage. Hard and

brittle rubber, cracking, tears, cuts, abrasions,

and excessive swelling indicate deterioration.

Particular attention should be paid to examine

those hose surfaces nearest to high heat sourc-

es, such as the exhaust manifold.

Inspect the hose routing to assure that the

hoses do not come in contact with any heat

source, sharp edges or moving component

which might cause heat damage or mechanical

wear. Inspect all hose connections, such as

clamps and couplings, to make sure they are

secure, and that no leaks are present. Hoses

should be replaced immediately if there is any

evidence of deterioration or damage.

F060H01A-AAT

o Air cleaner filter

A Genuine Hyundai air cleaner filter is recom-

mended when filter is replaced.

F060J01A-AAT

o Spark plugs

Make sure to install new spark plugs of the

correct heat range.

F060N01X-GAT

o Valve clearances

Incorrect valve clearance will not only result in

unsteady engine operation, but will also cause

excessive noise and reduced engine perfor-

mance. Inspect valve clearance and adjust as

required while the engine is hot.

Valve-to-rocker arm clearance

Intake valves ..... 0.008 in. (0.2 mm)

Exhaust valves .... 0.010 in. (0.25 mm)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hyundai Atos 2002 Seite 216

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info