Bedienungsanleitung I-onik WS-106 (Seite 5 von 6) (Deutsch, Englisch)

521907

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

8 9

3. Installation and Operation

3.1 Powering up the Flood Sensor

• Remove the battery cover; insert new batteries, noting the

polarity as shown in Fig. 1, and replace the cover. (Requires

2x AAA batteries).

• Low battery indication: If the batteries need to be replaced,

the RED LED on the transmitter will ash slowly.

3.2 Installing the Flood Sensor

• Mount the transmitter on a xed surface such as a wall using

either double-sided adhesive strips or the screws and wall

plugs provided.

• When mounting the water sensor part of the Flood Sensor use

the double-sided adhesive pad. If mounting onto on a porous

surface such as wood or concrete, make sure the surface is

painted to provide proper adhesive bonding.

• After installing, test the Flood Sensor using a bowl of water to

be certain it is working properly.

3.3 Installing using Double-Sided Adhesive Pads

• Ensure the mounting surface is clean.

• Peel back one layer of the protective lm and attach it to the

transmitter.

• Peel back the remaining layer of protective lm and press the

transmitter rmly in place against the mounting surface until

attached.

• Repeat the process to attach the water sensor.

4. House Security Code Settings

Unless the factory settings of the i.onik

Alarmsystem Smart

Panel have been altered, the house security code will NOT need

to be changed.

However, if the settings on the Smart Panel have been altered,

or need to be altered to solve the problem of the Smart Panel

and sensors activating intermittently (or not working at all) or

interference with other systems, then the house security code

on all system modules (sensors and sirens)will also need to be

changed.

House Security Code settings can be altered as follows:

• There are 4 jumpers or dip-switches on each device.

• Remove the jumper compartment cover, then pull out or plug

the jumper into the contacts to change the House Security

Code.

• If a jumper is plugged it is ON if it is removed it is OFF. Default

code is with all the jumpers plugged.

• To ensure the system works correctly, make sure the jumpers

on the Smart Panel and all other system modules (sensors and

sirens) match exactly.

Jumpers for

house

security code

- Smart Panel

- Each sensor

Default house code:

1: ON, 2: ON, 3: ON, 4: ON

*Jumper:

ON = Plugged,

OFF = Pull Out

Dip-Switches

for house

security code

- Key Fob Remote

Default house code:

1: ON, 2: ON, 3: ON, 4: ON

5. Zone Code Settings

The sensor is supplied with a pre-assigned zone setting.

The sensor can be assigned to a different zone as follows:

• Unscrew and remove the jumper compartment cover on the

rear of the sensor.

• In the area marked “Zone Code” there are eight pairs of

metal contacts with a number next to each.

• The number corresponding to the pair of contacts which is

plugged with a jumper is the current zone.

• To re-assign to a different zone simply unplug the jumper

from its current zone and plug it across the contacts corres-

ponding to the new zone number selected.

Jumpers for

zone code

Default zone code: Zone 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

I-onik WS-106 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info