12346
70
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
57
6
FUNCTIONS FOR TRANSMIT
2001 NEW 2001 NEW
Speech compressor
The speech compressor increases average RF output
power, improving signal strength and readability in
SSB, AM or FM.
When adjusting the compression level, it is necessary
to turn the COMP meter ON in the set mode, in ad-
vance (p. 81).
In SSB mode
q Select USB or LSB mode and adjust [MIC GAIN] to
a suitable level.
w While M1 is selected, push [F3 CMP] to turn the
speech compressor ON.
•“COMP appears.
e Push [F3 CMP] for 1 sec. to select compression
level set mode.
r While speaking into the microphone, rotate the tun-
ing dial, so that the COMP meter reads within the
COMP zone with your normal voice level.
Push [F3] for 1 sec. to select the default value.
When the COMP meter peaks above the COMP
zone, your transmitted voice may be distorted.
t Push [MENU] to return to M1.
In AM/FM mode
q While M1 is selected, push [F3 CMP] to turn the
speech compressor ON.
•“COMP appears.
w Push [F3 CMP] for 1 sec. and set the compression
level as 1 in advance.
e While speaking into the microphone, rotate [MIC
GAIN], so that the COMP meter does not exceed
the center dot whether you speak softly or loudly.
r While speaking into the microphone, rotate the tun-
ing dial, so that the COMP meter reads within the
COMP zone with your normal voice level.
Push [F3] for 1 sec. to select the default value.
When the COMP meter peaks above the COMP
zone, your transmitted voice may be distorted.
t Push [MENU] to return to M1.
Transmit lter width selection
(SSB mode only)
The transmit lter width for SSB mode can be selected
from wide, middle and narrow.
q Select USB or LSB mode.
w Push [MENU] to select M1, if necessary.
e Push [F4 TBW] for 1 sec. to select the transmission
passband width.
One of TX BW=WIDE, TX BW=MID or TX
BW=NAR is displayed for approx. 1 sec.
Transmit lter width: NAR 2.2 kHz
MID 2.4 kHz
WIDE 2.8 kHz
COMP
Level
COMP
Level
5
1
Compressor indicator
Shows compression level
COMP level zone
*The SWR meter functions as the COMP meter
when COMP meter is set to ON in the set mode.
COMP meter
ALC meter
Adjust the COMP Level with the tuning dial so
that the COMP meter does not exceed the COMP
level zone.
Adjust [MIC GAIN], so that the COMP meter does
not exceed this zone.
F 1
F
2F
3
F
4
F
5
F 1
F 2 F 3 F 4 F 5
AGC
DUP
CMP
TBW
SCP
AGC
DUP
CMP
TBW
SCP
TX
BW=WIDE
Push [F4]
Push [F4] for 1 sec. to select the transmit filter width.
The selected transmit filter width
is displayed for approx. 1 sec.
IC-7400.qxd 02.4.2 11:35 Page 57
70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Icom IC-7400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info