Bedienungsanleitung Icom IC-7600 (Seite 38 von 180) (Englisch)

670162

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

D Band edge warning beep

When you tune inside or outside of an amateur band’s

frequency range, a warning beep sounds. (“ ”

may be indicated on outside of an amateur band’s fre-

quency.) (p. 14)

This function can be turned OFF in set mode, if desired.

q Push [EXIT/SET] several times to close a multi-

function screen, if necessary.

w Push [SET] (F-6) to select set mode menu screen.

• Pushing and holding [EXIT/SET] for 1 sec. also selects

set mode menu screen.

e Push [OTHERS] (F-5) to enter others set mode.

r Push [Y] (F-1) or [Z] (F-2) to select “Beep (Band

Edge).”

t Rotate the main dial to select the band edge warn-

ing beep function.

y Push [EXIT/SET] to exit the set mode.

The beep output level can be set in level set mode.

(p. 123)

When the band edge warning beep is set to “ON”:

The

band edge warning beep sounds (enter: Pi, exit:

Bu) according to the set mode setting as follows.

• ON (Default)

Band edge beep sounds when an operating frequency

enters or exits the default amateur band. (default)

• ON (User)

A beep sounds when an operating frequency enters or

exits an amateur band that is set in band edge screen.

• ON (User) & TX Limit

Same as the setting of “ON (User).” However, the

transmission can be made in the set frequency

range only.

To programming the band edge:

hen “ON (User)” or “ON (User) & TX Limit” is

selected, [BAND] appears in the display above the

function switch (F-5), and up to 30 band edge fre-

quencies can be set in band edge screen.

Perform the steps q to t as above, then select

“ON (User)” or “ON (User) & TX Limit.”

w Push [BAND] (F-5) to enter the band edge screen.

e Push [Y] (F-1) or [Z] (F-2) to select the desired

band edge.

• Push [Ω ≈] (F-3) to select the set content for band

edge, lower or upper.

•

Push [INS] (MF6) to

insert a new blank band edge line.

• Push and hold [DEL] (MF7) for 1 sec. to delete the

selected band edge l

ine.

• Push and hold [DEF] (F-4)

for 1 sec. to display the

band edge initialize screen. Then, push and hold

[OK] (F-5) to initialize all band edge frequency settings.

r Input the desired frequency with the keypad.

• Push [GENE •] to input “. (decimal point)” between the

MHz units and kHz units.

• Program the frequency in ascending order.

• The frequency that is duplicated or out of an amateur

band cannot be programmed.

t Push [EXIT/SET] to exit the set mode.

When the transverter function is in use, the band

edge warning beep sounds with the default setting.

Main dial

F-1 F-2

F-6

EXIT/SET

SET

F-5

OTHERS

Main dial

EXIT/SET

F-5

F-1 F-2 F-3 F-4

DEF

[INS][DEL]

Keypad

BAND

• Band edge screen

NOTE: All frequency ranges are set in default. So

you should delete or change it to add the desired

band edge frequency.

ON (Default) (default)

BASIC OPERATION

ON (User)

Appears

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Icom IC-7600 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info