Bedienungsanleitung Icom IC-F3400D (Seite 140 von 182) (Englisch)

670354

140

Zoom out

Zoom in

Vorherige Seite

1/182

Nächste Seite

Bluetooth

OPERATION

11-5

Turning ON the Bluetooth

function

Mobile:

Step 1: Entering the Bluetooth

Set mode

(Transceiver)

1. Turn OFF the transceiver.

2. While holding down [F2] and [F3], turn ON the

transceiver. Continue holding down [F2] and [F3]

for about 3 seconds.

• 2 beeps sound.

Step 2: Entering the Pairing mode

(Bluetooth

device)

L See the Bluetooth

device’s instruction manual for

details.

Step 3: Turning ON the Bluetooth

function

(Transceiver)

3. After the headset has entered the Pairing mode,

hold down [F1] for 1 second to enter the Set

mode.

4. Push [F2] or [F3] to select “b0.”

5. Push [Up] to turn ON the Bluetooth

function.

• The transceiver automatically enters the Pairing mode,

and begins searching for a Bluetooth

headset.

• While searching, the status indicator quickly blinks

blue.

L If the status indicator does not blink after pushing

[Up], the transceiver has not entered the Bluetooth

Set mode. In that case, do steps 1 and 2 again.

L If the transceiver has been paired with a Bluetooth

headset before, the transceiver does not start

searching. In that case, the transceiver and the

headset are automatically connected.

Step 4: Pairing with a headset (Transceiver)

When a headset is found, the transceiver pairs with it.

• After the transceiver and the headset pairing has

succeeded, the Status indicator slowly blinks blue 3 times.

In that case, the connection to the headset has also

succeeded.

LThetransceiversearchesforaheadsetrst.After

searching for a headset, the transceiver will start

searching for a data device. To skip searching for a data

device, push [PTT] on the headset.

L If the Bluetooth

connection fails, the Status indicator

slowly blinks red 3 times. To search for a headset again,

push [Down] to turn OFF the Bluetooth

function, then

push [Up] to turn it ON again.

Step 5: Pairing with a data device (Transceiver)

1. When a data device is found, the transceiver pairs

with it.

• After the transceiver and the data device pairing has

succeeded, the Status indicator slowly blinks blue 3

times. In that case, connection to the data device has

also succeeded.

L If the Bluetooth

connection fails, the Status indicator

slowly blinks red 3 times. To search for a PC again,

push [Down] to turn OFF the Bluetooth

function,

then push [Up] to turn it ON again. The transceiver

automatically tries to connect.

2. Hold down [F1] for 1 second to exit the Set mode.

3. Turn OFF the transceiver, then turn it ON again to

normally operate the transceiver.

D For the Portable Non-display types and Mobile Segment types (Continued)

F1 F2 F3

[Up]

[Down][F1] [F2] [F3]

Power key

TIP: To turn OFF the Bluetooth

function, push

[Down] when “b0” is selected in the Set mode.

Previous view

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Icom IC-F3400D Seite 140

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info