Bedienungsanleitung Icom IC-FR9020 (Seite 6 von 20) (Englisch)

670412

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

1 LCD DISPLAY

LCD display consists of 4 x 20 characters as shown.

Line 1: The incoming RSSI with 10 steps

Line 2: The output power levels with 10 steps

Line 3: The left 4 letters show channel numbers.

The middle 8 letters shows the channel name.

(If not programmed, it will be blank.)

The right 4 letters displays the status of the ra-

dio as described below.

a. RX mode:

M = Mix, both analog and digital can be

received

D = Only digital can be received

b. TX mode:

D = PTT digital transmission

A = PTT analog transmission

c. Monitor mode:

= Monitor off

S = Selective squelch

d. P25 squelch:

N = Normal squelch

S = Selective squelch

e. Low Voltage Icon:

= Low Voltage state (Icon ﬂashes with

ALM LED)

f. Key lock mode:

= Key lock (Not displayed if in Low

Voltage alarm)

g. Shift mode:

= SHIFT KEY ICON (reverts to normal

within 2 seconds)

Line 4: The left 2 letters show GPC (GROUP CALL),

AC (ALL CALL), IC (INDIVIDUAL CALL). The

right 18 letters displays the GROUP NAME, IN-

DIVIDUAL NUMBERS, and so on.

2 LED DISPLAY

The IC-FR9010/FR9020 has 5 LED's from left to

right.

DIGI = The LED is ON when receiving a digital sig-

nal

REP = The LED is ON when in repeat mode

(The IC-FR9010/FR9020 can be programmed

for SIMPLEX - SEMIDUPLEX - DUPLEX -

REPEATER on a per channel basis.)

ALM = The LED ﬂashes when an error on either TX

or RX occurs

TX = The LED is ON when in Transmit

BUSY = The LED is ON when receiving a signal

3 KEY CONTROLS

3.1 Key entry without [SHIFT] key

[0]–[9] = Channel numbers and individual call

address (target address)

[A] = P25 calls (Group Call, All Call, and

Individual Call)

[B] = The beginning and the end of indi-

vidual call number

[C] = TX Transmit mode (Clear or Secure),

only models with encryption

[D] = P25 mode (analog or digital TX)

[Q] = Cancel channel number, individual

number

[#] = Ending channel number, individual

number

[CH] = Channel number entry, depress CH,

then 0–9 for channels

[F] (Scan) = P25 Conventional Control Messages

(SBC)

[MON] = monitor ON or OFF

Rotary knob = Volume, Squelch, Back Light Dimmer

and Timer

3.2 Key entry following [SHIFT] key

[0] = P25 test mode start and ﬁnish

[1] = Backlight ON/OFF

[2] = TX power HIGH/LOW

[3] = Talkaround ON/OFF

[4] = Change

[5] = No function

[6] = No function

[7] = Indicates Analog channel data

[8] = Key lock ON/OFF

[9] = No function

[A] = Manual CWID send key

[B] = Programmed CWID Start/Stop key

[C] = Cryptogram Test

[D] = No function

[Q] = Indicating P25 data (while de-

pressed)

[#] = DTMF Entry

[CH] = Toggle Bar-Graph or TX RX Fre-

quencies

[F] (Scan) = SBC (Conventional Control Messag-

es) Log/Emergency Call

[MON] = P25 squelch normal or selective and

analog MONITOR modes

RX = = = = = = = = = =

TX = = = = = = = = = =

C001 TAC 2 MD N

GPC 500

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Icom IC-FR9020 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info