12680
24
Zoom out
Zoom in
Vorherige Seite
1/78
Nächste Seite
16
6
DSC PREPARATION
2001 NEW
Position and time programming
q While pushing and holding [MODE
SET
] push
[POWER] to enter initial set mode.
Turn the power OFF in advance.
w Rotate [GRP] to select the GPS DISPLAY then
rotate [CH] to select the desired position indication
type from simple and detail.
e Rotate [GRP] to select the OFFSET TIME then
rotate [CH] to set the time difference between local
and the UTC times within 12 to +12 hours in
10 minute steps.
r Turn the power OFF once, then ON again to exit
quick set mode.
When a position and the UTC time data
(NMEA0183 ver. 3.01 format) is applied to [GPS],
the following steps are not necessary.
t Push [DSC] to select DSC watch mode.
y Push [MODE
SET
] to enter the DSC menu.
DSC menu is displayed as below.
u Rotate [CH] to select Position, then push
[ENT].
i Enter your position and the UTC time via the key-
pad, then push [ENT]
Push [3
SCAN
] for the East, [9
H
i] for the West, [6
RF
-
G
]
for the North and [7
L
o] for the South setting.
Degrees and minutes digits can only be entered even
when DETAIL is selected for the position indication
in step w the seconds digits show 0 only.
Rotate [CH] to move the cursor.
o Push [ENT] to program the position and time.
Return to the DSC MENU indication as in step u.
!0 Push [MODE
SET
] to exit the DSC menu.
Rotate [CH] to select Exit then push [ENT] also
exits set mode.
•“MNL appears instead of GPS.
*******
Position
*******
---
Position
&
time
----
Latitude
Longitude
UTC
34
34'N
135
34'E
12:34
OKNull
*******
DSC
MENU
*******
--------
Select
--------
Position
Individual
Group
All
ships
Position
REQ
Distress
Ç
OKSEL
***
SET
MODE
***
ITEM SEL
***
SET
MODE
***
SIMPLE
DETAIL
ÇÇ
ITEM SEL
[POWER][MODE SET]
When no position and the UTC (Universal Time Coor-
dinated) time data in NMEA0183 ver. 3.01 format, such
as from a GPS receiver, etc., is applied to [GPS] con-
nector, your position and the UTC time should be input
for DSC operation.
IMPORTANT!
The manually programmed position and the UTC
time settings will be cleared once the power is
turned OFF. They are never renewed during the
voyage when the position is set manually.
IC-M802_USA.qxd 02.7.9 10:58 Page 16
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Icom IC-M802 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info