Bedienungsanleitung Icom IC-R8600 (Seite 88 von 96) (Englisch)

670434

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

16-1

[10.7 MHz OUT]

Outputs the 10.7 MHz IF signal for

an external detector/demodulator circuit.

• Center frequency: 10.7 MHz

• Band width*: 10 MHz

• Impedance: 50 Ω (unbalanced)

• Maximum output level:－10dBm (approximately)

*The band width is xed regardless of the digital PBT lter setting.

[REF I/O 10 MHz]

Outputs or inputs a 10 MHz

reference frequency signal.

You can change the signal direction

in the Set mode.

• Center frequency: 10 MHz

• Impedance: 50 Ω (unbalanced)

• Input/Output level: –10 dBm (approximately)

• Frequency stability:

±0.5 ppm

(–10°C ~ +60°C, +14°F ~ +140 °F)

[I/Q OUT]

Outputs the Phase/Quadrature data which is

processed by the FPGA.

Connect a PC's USB port, to demodulate the DRM

broadcast or Software Dened Radio SDR.

• Interface: USB (1.1/2.0), type B

Icom does not provide any support regarding SDR technology and

related software, except the inspection for the normality of output signal.

L The IQ driver and instruction guide will be released on the Icom

website near future.

http://www.icom.co.jp/world/index.html

[AF/IF]

Outputs the demodulate audio signal or 12 kHz IF

signal (unltered). The output level is xed, regardless

of the volume control position. (3.5 mm, 1/8 in (d))

• Impedance: 4.7 kΩ

• Output level: 100 ~ 300 mV (RMS)

LYou can select the output signal from AF or IF signals.

» SET > Connectors > AF/IF

LThe signal is also output from [USB] (front or rear) or [LAN].

[USB]

2 USB ports: Type B mini and Type B.

L You can download the USB driver and installation

guide from the Icom website.

http://www.icom.co.jp/world/support/download/rm

• Outputs the decoded FSK (RTTY) signal, or D-STAR data.

• Outputs the demodulated signal or 12 kHz IF signal.

• Remote control interface for optional RS-R8600 (feature product).

• Programming interface for the optional CS-R8600.

L You can change the port settings (FSK decode data/D-STAR data,

AF/IF), baud rate and output level)

» SET > Connectors > USB (Front)

» SET > Connectors > USB (Rear)

[LAN]

LED indication:

LINK/ACT Lights: Cable connected.

Doesn't light: Cable not connected.

Blinks: While the line is communicating.

Speed Lights: Communicating in 100BASE-TX

Doesn't lights: Communicating.

in10BASE-T, or not connected.

• Time synchronization by an NTP server.

• Outputs the demodulated signal or 12 kHz IF signal.

• Remote control interface for the optional RS-R8600 (future

product).

LYou can select the output signal from AF and IF signals.

» SET > Connectors > LAN

[MUTE] JACK / [MUTE] SWITCH

Used to mute the receiver

output.

(3.5 mm, 1/8 in (d))

When the Mute Switch is slid to right, the receiver

enters to the Bit Error Rate (BER) Measurement mode

for the maintenance purpose.

When the [MUTE] is slid to left:

When this terminal is grounded, the receive circuit is turned OFF.

L Use this function when you use the IC-R8600 with a transceiver.

LThe sink current is approximately 1 mA at 8 V input.

When the [MUTE] is slid to right:

Connect a BER counter. In the BER Measurement mode,

the PN9 bit stream is output from this terminal.

[METER]

Connects to an external meter.

Outputs the received signal

strength or squelch level.

(3.5 mm, 1/8 in (d))

• Output voltage: 8 V (maximum)

• Output impedance: 10 kΩ

L You can select the output signal from received signal strength

and squelch levels.

SET > Connectors

q w

CONNECTOR INFORMATION

BNC type

On the front panel

miniB type B type

On the rear panel

Meter output

Mute

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Icom IC-R8600 Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info