Bedienungsanleitung Icom ID-51A (Seite 395 von 413) (Englisch)

689583

395

Zoom out

Zoom in

Vorherige Seite

1/413

Nächste Seite

20-1

TROUBLESHOOTING

The following chart is designed to help you correct problems which are not equipment malfunctions.

If you are unable to locate the cause of a problem or solve it through the use of this chart, contact your nearest Icom

Dealer or Service Center.

DWhile operating D-STAR

PROBLEM POSSIBLE CAUSE SOLUTION REF.

After your call, the repeater

does not return a status re-

ply.

• The repeater setting is wrong.

• The manually entered repeater fre-

quency, frequency offset, or duplex set-

ting is wrong.

• Your transmission did not reach the re-

peater.

• Select the correct repeater.

• Correct the repeater frequency, fre-

quency offset, or duplex setting.

• Wait until you are closer to the repeater

and try again.

• Try to access another repeater.

p. 8-2

pp. 9-30, 9-31

—

After your call, the repeater

replies ‘UR?’ and its call

sign.

• The call was successfully sent, but no

station immediately replied.

• Wait for a while, and try again. —

After your call, the repeater

replies ‘RX’ or ‘RPT?’ and

the access repeater’s call

sign.

• Your own call sign (MY) has not been

set.

• Your own call sign (MY) has not been

registered on a gateway repeater, or the

registered contents do not match your

transceiver’s setting.

• Set your own call sign (MY).

• Register your own call sign (MY) on a

gateway repeater, or conﬁrm the regis-

tration of the call sign.

p. 13 of the

Basic manual

p. 15 of the

Basic manual

After your call, the repeater

replies ‘RPT?’ and call sign

of the destination repeater.

• The repeater cannot connect to the

destination repeater.

• The repeater is busy.

• Check the repeater setting.

• Wait for a while, and try it again.

p. 9-23

—

After your call, the access

repeater replies ‘RPT?’ and

its call sign.

• The call sign of the destination repeater

is wrong.

• Correctly set the destination repeater

call sign.

p. 9-28

Even holding down , the

DR function is not selected.

• There is no Repeater List in your trans-

ceiver.

• Reload the Repeater List using the CS-

51PLUS2 cloning software on the CD.

• Reload the Repeater List using a mi-

croSD card.

• Enter the Repeater List data directly

into the transceiver.

p. 17-20

p. 8-21

p. 9-24

Even holding down , the

received call sign will not set

to the destination call sign.

• The call sign has not been correctly re-

ceived.

• When a received signal is weak, or a

signal is received during scanning, the

call sign may not be received correctly.

In that case, “--------” appears and error

beeps sound, and a reply call cannot be

made.

• Try it again, after the transceiver has

correctly received the call sign.

—

A Local area call can be

made, but the Gateway call

or destination station call

cannot be made.

• MY call sign has not been registered on

a D-STAR repeater.

• Register your own call sign (MY) on a

gateway repeater, or conﬁrm the regis-

tration of the call sign.

p. 13 of the

Basic manual

During transmission, “L” ap-

pears on the LCD, and the

received audio is interrupted.

• While receiving through the internet,

some packets may be lost due to net-

work error (poor data throughput per-

formance).

• Wait a while, and try it again.

When the transceiver receives cor-

rupted data, and misidentiﬁes it is as

Packet Loss, “L” is displayed, even if it

is a Local area call.

—

“DV” and “FM” icons alter-

nately blink.

• While in the DV mode, an FM signal is

received.

• Use a different operating frequency un-

til there are no FM signals on the origi-

nal frequency.

p. 9-10

Previous view

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Icom ID-51A Seite 395

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Icom ID-51A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info