Bedienungsanleitung Ignis AKS 101 (Seite 2 von 4) (Englisch)

611556

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

The cooktop should not be forced into the

worktop. Forcing the glass-ceramic top may cause

it to crack (even at a later date)!

• If the worktop is made of wood

, use the spring

clips and screws provided (Fig. 7).

Secure the spring clips (D) (Fig. 7) with the

screws provided (E) (Fig. 7) as shown, paying

attention to the specified distances.

Fit the cooktop into the worktop.

• If the worktop is made of marble, plastic,

ceramic, stone, etc.

, the cooktop must be

secured with special brackets (F) (Fig. 7), Code

4819 404 78697 available at After Sales Service.

Fit the cooktop into the worktop.

Place the 4 brackets (F) in position in

accordance with the thickness of the worktop

as shown in Fig. 8.

Fasten the 4 screws (G) in the positions (H)

(Fig. 8).

Electrical connection

Regulations require that the appliance be

earthed.

•

Connection to the mains must be carried out by

a qualified technician in accordance with the

manufacturer’s instructions and in compliance

with local regulations.

•

The installer is responsible for connecting

appliances correctly to the mains and for

observing the safety regulations.

•

The oven power cable must be long enough to

connect the built-in appliance to the mains.

•

Observance of safety directives requires that a

multi-pole switch with a minimum contact gap of

3mm be used for the installation.

•

Do not use multiple plug adapters or extension

leads.

•

After the oven has been installed, the electrical

components must be inaccessible.

Connecting the oven to the power

supply

•

Make sure that the voltage indicated on the rating

plate is the same as the mains voltage. The rating

plate is on the front edge of the oven (visible

when the door is open).

Remove the two fastening screws of the

terminal box cover located on the bottom part

of the oven’s rear covering.

Remove the cover to gain access to the terminal

box and insert the power cable (see table)

through the opening located on the bottom of

the oven.

Connect the cable to the terminal box, tighten

the screws as far as they will go and secure it to

the cable fastener.

Put the cover back on by inserting the two blades

in the slots and fasten it with the two screws.

Interconnecting cooktop and oven

Important: do not connect the oven to the

power supply before you have finished

connecting the oven and cooktop.

•

Before connecting the oven to the power supply,

make sure that the cooktop is among the ones

listed in the cooktop/oven pairing product sheet

provided.

•

Remove the cover (L) (Fig. 9) (if present) of the

connectors (D) (Fig.9) located on the top covering

of the oven by loosening the fastening screw (M)

(Fig. 9). Lift up the cover (L) to gain access to the

connectors (D) and connect the connectors of the

cooktop (C) (Fig. 9) to the connectors of the oven

(D), matching the colours and alignment of the

housing guides visible on top of the connectors.

•

Then make the connection by pushing the

connectors all the way in, making sure that the

tongue clicks into place. Put the cover (L) back and

let the cables stick out from the bottom. Fasten

the cover with the screw removed previously.

•

Unscrew the nut of the ground screw (K) (Fig. 9)

on the top covering of the oven and insert

the yellow/green ground cable, leaving the

washer in place. Screw the nut back onto the

screw and tighten it as far as it will go.

Important:

If the cooktop terminals do not

correspond to the connection and colour

indications on the cooktop/oven connection plate

located at the top of the oven, request the adaptor

kit, code

AMC 873

, from the After-sales Service.

Securing the oven

•

Lift up the oven getting hold of it by the openings on

the sides and insert it into the housing unit, being

careful not to trap the power supply cable (Fig.10).

•

Center the oven in the housing unit before

securing it.

•

Make sure that the plastic spacers (if provided)

are positioned correctly in the fastening holes.

Then anchor the oven to the housing unit with

the screws provided.

Power supply cable table

N° of conductors Type of cable

1N+

H05 RR-F 3 X 4 mm²

2N+

H05 RR-F 4 X 2.5 mm²

3N+

H05 RR-F 5 X 1.5 mm²

H05 RR-F 4 X 2.5 mm²

10200157aGB.fm Page 4 Monday, September 5, 2005 3:53 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ignis AKS 101 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ignis AKS 101

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info