By ensuring this product is disposed of correctly, you will help prevent
negative consequences for the environment and human health.
The symbol on the product or on the accompanying documentation
indicates that it should not be treated as domestic waste but must be
taken to an appropriate collection center for the recycling of electrical
and electronic equipment.
ENERGY SAVING TIPS
Make the most of your hot plate’s residual heat by switching it o a few
minutes before you nish cooking.
The base of your pot or pan should cover the hot plate completely; a
container that is smaller than the hot plate will cause energy to be wasted.
Cover your pots and pans with tight-tting lids while cooking and use
as little water as possible. Cooking with the lid o will greatly increase
energy consumption.
Use only at-bottomed pots and pans.
DECLARATION OF CONFORMITY
This appliance meets Ecodesign requirements of European Regulation
66/2014 and The Ecodesign for Energy-Related Products and Energy
Information (Amendment) (EU Exit) Regulations 2019 in compliance with the
European standard EN 60350-2.
INSTALLATION
EN
• The cooktop must be set into a worktop at least 20 mm deep.
• There must be nothing between the cooktop and the oven (cross rails, brackets, etc.).
• Make sure the power cord is long enough to allow convenient installation.
• The distance between the lower face of the glass ceramic hob and the cupboard or separating
panel must be at least 20 mm.
• For built-in dimensions and installation see the picture in this paragraph.
• A minimum distance must be maintained between the hob and the hood above it. Please refer to
the user manual of the hood for more informations.
• Apply the supplied gasket to the cooktop (unless it has already been tted), after having cleaned its surface.
• Do not install the cooktop near a dishwasher or washing machine, so that the electronic circuits do not come into contact with steam
or moisture, which could damage them.
• If an oven is installed beneath the cooktop, make sure that it is equipped with a cooling system. If the temperature of the electronic circuits
exceeds the maximum permitted temperature, the cooktop will switch o automatically; in this case, wait for a few minutes until the internal
temperature of the electronic circuits reaches a tolerable level, at which point it will be possible to switch the hob on again.
PLACING THE HOB
After the electrical connection (see the chapter “Electrical connection”), position each xing clips on the dedicated slots on the lateral sides of the
hob as shown in the picture. Then push the hob inside the cut out and check that the glass is at and parallel to the worktop. The xing clips are
designed for every type of worktop material (wood, marble, etc.).
4x
12
DIMENSIONS AND DISTANCES TO BE MAINTAINED
Min. 40 cm
L
Min. 5 cm
Min.10 cm
i
552 mm
42 mm
512 mm
582 mm
Min. 6,5 mm
Max. 8 mm
490 - 492 mm
560 - 562 mm
Min. 50 mm
Min.
20 mm
482 mm
REMOVING THE HOB:
To remove the hob, rst, disconnect it from the electric supply. It is strongly recommended to free the underneath part from the oven, drawer,
separator, or other. It allows the technician to access the lower part of the hob to unfasten the four clips with a screwdriver, lift the hob and remove
it, avoiding any worktop damage.
min. 20 mm
PRODUCT DESCRIPTION
ELECTRICAL CONNECTION
Electrical connection must be made before connecting the appliance to the electricity supply.
The power cord is not included in the package - remember to prepare your own power cord.
Installation must be carried out by qualied personnel who know the current safety and installation regulations. Specically, installation must be
carried out in compliance with the regulations of the local electricity supply company.
Make sure the voltage specied on the data plate located on the bottom of the appliance is the same as that of the home.
Regulations require that the appliance be earthed: use conductors (including the earth conductor) of the appropriate size only.
CONNECTION TO THE TERMINAL BLOCK
For the electrical connection, use an H05RR-F or H05V2V2-F cable as specied in the table below.
SUPPLY VOLTAGECONDUCTORS
AMOUNT x SIZE
220-240V ~ + 3 x 4 mm2
230-240V ~ + 3 x 4 mm2 (Australia only)
220-240V 3~ + 4 x 1,5 mm2
380-415V 3N~ + 5 x 1,5 mm2
380-425V 2N~ + 4 x 1,5 mm2
The appliance must be connected to the electricity supply by means of an all-pole disconnect switch with minimum contact gap of 3 mm.
ATTENTION: the power supply cable must be long enough to allow the cooktop to be removed from the worktop and must be positioned so as to
avoid damage or overheating caused by contact with the base.
NOTE: the yellow/green earth wire must be connected to the terminal with the symbol and must be longer than the other wires.
• Remove approx. 70 mm of the cable sheath from the power supply cable (B).
• Strip approx. 10 mm of sheath from the wires. Then insert the power supply cable into the cable clamp and connect the wires to the terminal
block as indicated in the connection diagram placed close to the terminal block itself.
• Secure the power supply cable (B) by means of the cable clamp.
• Close the terminal board with the cover (A) securing it with the screw provided.
• After the electrical connection, t the hob from the top and hook it to the support springs, according to the illustration.
A
B
210 mm
180 mm
145 mm
145 mm
CONTROL PANEL
B
B
E
E
A
A
C
C
D
D
AOn/O
BCooking zone and timer selection
C-EHeat setting increase and decrease
DKey lock
DAILY USE
SWITCHING THE HOB ON/OFF
To switch the hob on, keep button “A“ pressed for approx. 2 seconds. The
4 cooking zone displays show “0“. If within 20 seconds none of the cooking
zones is activated, the hob switches o automatically as a safety precaution.
SWITCHING ON AND ADJUSTING COOKING ZONES
Press one of the buttons “B“ corresponding to the cooking zone you
intend to use. Select the heat setting required with buttons “E“ or “C“.
The other selectable cooking settings go from 1 to 9. Press buttons “+/−“
at the same time to cancel all settings.
IMPORTANT: the control is deactivated 10 seconds after the heat setting has
been selected.
To change the heat setting, rst press the selection button “B“ again, then
proceed to change the setting, using buttons “E“ or “C“.
TIMER
To set the Timer function, select the desired cooking zone and power
setting then press the cooking zone key again and a luminous dot
will appear on the display of the timer-controlled cooking zone. The
indication “00“ blinks on the 2 displays. Press buttons “C“ or “E“ to set
the time from 1 to 99.
IMPORTANT: after 10 seconds the timer displays will show the power
setting of the other cooking zones.
To view the remaining cooking time, press the timer-controlled cooking
zone key twice.
A FUNCTION
This function allows to automatically decrease the cooking zone power
level from the highest value (level 9) to the one selected by the user for
a later stage of cooking.
To activate this function rst press the “+“ button when level 9 is reached.
The display shows “A“ and “9“ ashes alternately with low brightness.
At this point, choose the desired power level (less than 9) with the “–“
button.
“A“ and selected level ash alternately with low brightness on the display.
The function is activated once “A“ and the selected level ash alternately
with high brightness on the display.
Once “A“ is no longer visible on the display (the “A“ function switches o
automatically after several minutes, depending on the set power level),
the cooking process continues with lower power and the display shows
only the selected power level.
N.B.: this function is not possible with level 9.
KEY LOCK
The Key lock function is switched on by holding down button “D“ until
a dot lights up above the function button. The control panel is locked
except for the switching-o function. The function remains on even after
the hob is switched o and on again and can be deactivated by pressing
button “D“ again until the dot above the function button goes o.
When the hob is o with the key lock activated to switch the hob on, rst
deactivate the key lock function by pressing button “D“ again until the
dot above the function button goes o.
The presence of water, liquid spilled from pots or any objects resting on
the controls can accidentally activate or deactivate the Key lock function.
RESIDUAL HEAT INDICATOR
When the cooking zone is switched o, the residual heat indicator “H“
remains on or ashes alternating with “0“ until the temperature of the
hob returns within safety levels.
IMPORTANT: The hob’s safety features include an automatic switching
o function. Prolonged use of the same heat setting triggers automatic
switch-o of the cooking zone (for example, after around 1 hour at
maximum heat setting, the cooking zone switches o).
IMPORTANT: To avoid a permanent damage the hob:
• do not use pots with bottoms that are not at;
• do not use metal pots with enamelled bottom;
• do not place hot pots/pans over the control panel.
FIRST TIME USE
Upon the rst installation, the control panel performs a functional test for
about 1 second, after which it automatically switches to the “Key lock“
function.
To deactivate the function, press and hold button “D“; an acoustic signal
will sound, and the corresponding led will turn o.
NOTE: If a reset occurs, repeat the procedure described above.
EN
POWER LEVEL TABLE
POWER LEVELTYPE OF COOKINGLEVEL USE
(indicating cooking experience and habits)
Maximum
power
9Boiling
Ideal for rapidly increasing the food temperature to fast boiling in the case of
water or rapidly heating cooking liquids.
9
−
8SearingIdeal for browning, starting to cook, frying frozen products, fast boiling.
High power
8
−
7Browning – maintain boiling –
grillingIdeal for browning, maintaining a high boil, cooking, and grilling (short
duration, 5-10 minutes).
7
−
6Frying – cooking – grillingIdeal for maintaining a low boil, cooking and grilling (medium duration, 10-20
minutes), preheating, and frying.
Medium power
6
−
5Gentle fryingIdeal for frying eggs, omelettes.
5
−
4Cooking – simmering – stewingIdeal for prolonged cooking (rice, sauces, roasts, sh) with liquids (e.g., water,
wine, broth, milk), creaming pasta.
4
−
3Thickening – creaming pasta
Low power2
−
1Keeping food hot – creaming
risottosIdeal for keeping just-cooked food hot (e.g., sauces, soups, minestrone),
creaming risottos and keeping serving dishes warm.
Minimum
power1DefrostingIdeal for defrosting small products and gently melting chocolate or butter.
Zero power 0
−
Hob in stand-by or o mode (possible end of cooking residual heat, indicated
by an “H“).
The hob is also equipped with the “auto shut o“ function that switches o the cooking zone if no power level modication is done after a specic
time frame depending on the power setting itself. In the table, there is the time duration of each power level.
POWER LEVELAUTO SHUT OFF TIME
030 seconds
110 hours
25 hours
35 hours
44 hours
53 hours
62 hours
72 hours
82 hours
91 hour
MAINTENANCE AND CLEANING
Disconnect the appliance from the power supply.
• Do not use steam cleaning equipment.
• Do not use abrasive sponges or scouring pads as they may damage
the glass.
• After each use, clean the hob (when it is cool) to remove any deposits
and stains from food residue.
• Sugar or foods with a high sugar content can damage the hob and
must be immediately removed.
• Salt, sugar and sand could scratch the glass surface.
• Use a soft cloth, absorbent kitchen paper or a specic hob cleaner
(follow the Manufacturer’s instructions).
• Spills of liquid in the cooking zones can cause the pots to move or
vibrate.
• After cleaning the hob, dry thoroughly.
AFTERSALES SERVICE
To receive complete assistance, please register your product on
www . whirlpool.eu/register.
BEFORE CALLING THE AFTER-SALES SERVICE:
1. See if you can solve the problem by yourself with the help of the
TROUBLESHOOTING suggestions.
2. Switch the appliance o and back on again to see if the fault persists.
IF AFTER THE ABOVE CHECKS THE FAULT STILL OCCURS, GET IN
TOUCH WITH THE NEAREST AFTER-SALES SERVICE.
To receive assistance, call the number shown on the warranty booklet or
follow the website’s instructions on www . whirlpool. eu.
When contacting our Client After sales service, always specify:
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Ignis AKS 309 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.