ADJUSTMENT
OF
THE TEMPERATURE
The which is situated with the interior light on the
right hand side of the refrigerator compartment, allows the
temperature of the interior to be
Position
O
indicates that the operation of the appliance is inter-
rupted
(Fig. l-Bl). The higher the number the colder the
appliance.
To obtain the best storage of foods at an ambient temperatu-
re between 15 and 20°C. we suggest you adjust the thermo-
stat control knob to a mid position.
Internal temperatures are affected by the location of the ap-
pliance, the temperature of the surrounding air, the frequency
of door opening. The setting of the thermostat may to
be varied to allow for these factors.
USE
OF
THE REFRIGERATOR COMPARTMENT
All items stored in the refrigerator compartment should be
wrapped or or kept in a container.
This prevents food from becoming dry on the surface and stops
strong smells and flavours being transferred from one food to
.
another. The coldest of the refrigerator compartment
is
at the bottom near the glass separator. are best
stored in the following position
(Fig.
4):
Meat, sausages, fish,
etc.
should be stored at the bottom of the cavity, near the
glass shelf.
Cooked foods, meats, jellies, etc.
should be stored on the
top shelves.
Eggs, cheese and produces
should be stored in the
compartments in the refrigerator
Fruit and vegetables
should be stored in the crisper under-
neath the glass shelf.
Important:
Do
not place foodstuffs or containers
so
that they
restrict the free circulation of air within the appliance. Do not
cover the grids with paper or plastic. Allow cooked food to
cool before storing in the refrigerator
Canned food:
once the can has been transfer any
remaining food into a non-metallic container.
DEFROSTING THE APPLIANCE
Defrosting is completely automatic and requires no ma-
nual operation by
The defrost water flows down the rear wall through the liner
into a tray situated on top of the compressor where
it
evapo-
rates.
MAINTENANCE AND CLEANING
Periodic and maintenance will ensure a longer life for
your
When out clean'ing or any other
always disconnect the appliance from mains supply.
The refrigerator should be cleaned with a
dampened in a solution of lukewarm water and vinegar.
A
little
mist is not a periodically where the door closes.
Never use detergents or abrasive cleaners.
The outside of
the appliance should be with a if and when
necessary. After cleaning, the appliance should be dried care-
fully with a soft The grid) at the back
of the appliance should be cleaned periodically with a soft
brush or a
(Fig.
5).
Hints for holidays
If
you plan to be away for a long time the appliance should be
disconnected from the mains supply, empty clean the insi-
de. The door should be left open to prevent the appliance
from smelling musty.
If
you plan to be away for a short
the appliance can be left to operate normally.
HINTS FOR ENERGY SAVING
You can save energy when operating the appliance
-
Check the door gasket; level the appliance to ensure cor-
rect door closing.
-
Periodically the condenser.
-
Open the door only when necessary. Close it as soon as you
have removed food.
-
Do not overload the refrigerator: let air it.
-
Do not adjust the thermostat control knob to an excessive
cold position: you will waste
-
Ensure that the appliance is not installed
so
ce
such as cookers, or in direct sunlight.
"\
SERVICE
The of the appliance
is
not always due to a
fault, but it may also result of poor usage. To pre-
vent unnecessary service calls for which you will be charged, we
suggest you consult trouble shooting guide.
1.
The temperature in the compartment
is
not cold enou-
gh.
Check that:
-
the door is properly closed
-
the thermostat control knob is in the correct
(see chapter of the temperature).
-
the appliance is not too close to a heat source
-
the condenser (black grid), situated at the back of the appliance
is clean
-
the air flow on the top or around the applliance is not restricted
2.
The temperature in the compattment
is
too
cold.
Check that:
-the thermostat control knob
is
in the correct
3.
The appliance
is
excessively noisy.
Check that:
-
the appliance is not in with adjacent fitments which
may cause noise to vibration
-
the condenser (black grid) at the back of the appliance the
refrigeration system pipework at the rear of the cabinet are not
vibrating the cabinet each other.
Caution:
The refrigerator is equipped with a compressor that alterna-
tely stop and run
so
as to keep the inside
During the first months of operation the compressor may be noi-
sy but this will progressively wane and then disappear
tely. This noise is quite normal and it should not be considered as
a of the refrigerator.
4.
The appliance does not at all.
Check that:
-
there is not a power failure
-
the supply plug
is
making good contact with the supply socket
-
the socket has power, by connecting to it.
For Great Britain only
Check the fuse (if fitted). A fuse must be fitted to this
appliance. Try new fuse
-
check rewirable plugs for loose connec-
tions and tighten if necessary. connections can
overheating of the plug: has occurred replace the plug.
-
the supply is broken
(see also Note).
5.
The interior does not work.
Check point
4.
Unplug the appliance remove the lamp cover. Check that
the is not loose -tighten
it,
if necessary.
To
change the faulty bulb
-
(use a bulb of not more than 15W)
(Fig.
6-7):
carefully remove the lamp cover situated near the
thermostat the bulb and replace with a new one.
Note:
To the supply unplug the appliance and fit
the new cable, that it is fitted correctly.
If
you have followed the above checks and your
does not work properly, get in touch with the Service Division.
Addresses and telephone found on the Service
Registration or Booklet. State clearly what is wrong and
the type and serial number of your appliance
(Fig.
8).
DOOR REVERSIBILITY
Before this operation, disconnect the appliance from the
mains supply.
1) Remove the plug
2)
Remove the plinth
3) Fit the insert from left to right hand side
4) Tilt the appliance
5)
Take away the lower hinge pin screw with washer
6)
Remove the door (keep the upper spacer)
7) Remove the right hand side lower bush
8) Close the hole with the adhesive delivered in the bag.
9) out the left hand side bush from the bag and fit it
with the screw
1
O)
Fit the handle at the opposite side (A-B-C-D)
11) the right hand side lower pin and the plate
12) the plate by 180" and it on the opposite
hinge.
13) the pin
14) Unscrew the right hand side upper pin and fit it at the left
hand side
15) the spacer on the pin (see point
6)
16) Mount the door on the upper
17) Tighten the lower pin screw with washer
18) Mount the plug and fit the plinth
19) Change the position of feet.
