Bedienungsanleitung Ignis awv 516 (Seite 2 von 2) (Englisch)

311702

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 512 10017

Ignis is a registered trademark of Whirlpool USA.

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized

conditions in compliance with standard IEC 60 456. Consumption data in the home may vary with respect to the values in the

table in relation to the water supply pressure and temperature, the load and the type of wash. The data on the “Energy

Label” refer to the programme “Coloured Cotton 60°C”.

* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household

conditions applicable at that time.

** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains

the water out.

1. Close the drum flaps and check that they are

properly locked.

2. Add detergents and additives into the dispenser

to no more than the

“MAX”

level mark, as

follows:

• Programme with pre and main wash

• Main wash programme without prewash

• Fabric softeners and conditioners

• Chlorine bleach

• Stain remover agents

• Anti-scale agents (if necessary)

Turn the

programme selector knob

clockwise

to the desired programme.

Turn the

temperature knob

to the required

temperature.

“Eco Wash” button

• The wash time is extended and the water

temperature is reduced.

• This function saves about 30% in energy without

compromising the excellent results of the wash.

“Half Load” button

• Reduces the water consumption in the “Cotton”

and “Synthetics” programmes especially during

the rinse.

• Especially suitable for lightly soiled or small loads

(reduces the quantity of detergent).

• Not suitable for high temperature programmes.

“Rinse Hold” button

• The laundry remains in the last rinse water,

without progressing to the spin cycle to avoid

creasing and prevent colours from changing.

• This option is especially recommended for the

“Synthetics” or “Delicate” programmes.

• This option is perfectly suitable if you wish to

postpone the spin or you don't wish to spin the

clothes.

ENERGY AND WATER CONSUMPTION DATA

Programme Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Programme

time

(min)

Cotton 90 5.0 72 1.80 115

Cotton 60 5.0 72 1.15 115

Coloured 60 2.0 66 0.80 100

Coloured 40 2.0 66 0.40 100

Quick Wash + 1/2 Load 40 2.5 54 0.50 85

Synthetics + 1/2 Load 30 1.0 54 0.30 70

Delicate 40 1.5 70 0.65 55

Wool 40 1.0 70 0.55 45

PREPARATION OF WASH CYCLE PRESS ANY DESIRED OPTION BUTTON(S)

eco

Note:

the programme selector stops on “ ”.

Terminate the “Rinse Hold” option.

• Press the “Rinse Hold” button again; the

programme will terminate automatically with

the spin cycle corresponding to the previously

selected wash programme.

• If you do not wish to spin the clothes, switch off

the appliance by pressing the

“On/Off”

button.

The pilot light goes out. Turn the programme

selector to the “Drain” position and switch on

the appliance.

Open the water inlet tap and select the desired spin

speed, turning the spin speed and

“On/Off”

knob

to the desired position (the indicated spin speed or

“No Spin”). The pilot lamp lights up.

During the running programme, the door cannot be

opened.

The door locks automatically in all programmes.

If the programme is stopped or if an electrical

power failure occurs, the door unlocks

automatically after about 1 minute.

• The programme selector knob is at “STOP”,

the pilot lamp lights.

1. Turn the spin speed knob to the Off position

“ ”. The pilot light goes out.

2. Cancel the options by pressing the appropriate

buttons.

3. Turn the water supply tap off.

4. Wait for the door to unlock (about 1 minute).

5. Open the door and the drum flaps and unload

the machine.

1. Turn the spin speed knob to the Off position

“ ” to switch off the appliance.

The pilot light goes out.

2. Select the new programme, temperature and

options.

3. Turn the spin speed knob to the desired spin

speed to switch on the appliance.

The pilot light lights.

1. Turn the spin speed knob to the Off position

“ ” to switch off the appliance.

The pilot light goes out.

2. Set the programme selector on “Drain”.

Turn the spin speed knob to the desired spin

speed to start the “Drain” programme.

Only open the door when the programme

selector is at “STOP” and the door is unlocked

(after approximately 1 minute).

• After switching your washing machine on, it

does not start immediately: it needs some

seconds in order to lock the door, fill water and

then drum starts turning.

• Spinning has an interrupted start-up: the drum

starts and stops running several times, to

improve spin efficiency and to better balance

the laundry.

• At the end of the spinning cycle the drum goes

on reversing for some minutes: this helps you

unloading the laundry.

• Do not exceed in detergents dosage: excessive

foam formation may prevent spinning.

• The turning of the drum is stopped in several

steps of the washing cycle due to optimization

of energy consumption.

PROGRAMME START

DOOR LOCK

PROGRAMME END

SELECTING A NEW PROGRAMME, SPIN

SPEED, OPTIONS AFTER PROGRAMME

START

TO STOP, RESET A PROGRAMME BEFORE

THE END

NOTES AND INDICATIONS FOR USE

Ignis awv 516 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ignis awv 516

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info